PC LEXAN™ EXL1414-GY7D493
25
- Properties:ProcessabilityModerate liquidityDuctilitycopolymerGood demolding performanc
- Usages:currencyElectrical fieldElectronic field
Compare
View PricesTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|---|---|---|
| density | ISO 1183 | 1.19 g/cm³ | |
| ASTM D792 | 1.18 g/cm³ | ||
| Water absorption rate | ISO 62 | 0.35 % | |
| ISO 62 | 0.15 % | ||
| Shrinkage rate | 内部方法 | 0.40 到 0.80 % | |
| 内部方法 | 0.40 到 0.80 % | ||
| Molten Volume Flow Rate (MVR) | ISO 1133 | 9.00 cm3/10min | |
| melt mass-flow rate | ASTM D1238 | 10 g/10 min |
| hardness | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Rockwell hardness | ASTM D785 | 89 | |
| ASTM D785 | 121 |
| flammability | Test Condition | Test Method | Test Result |
|---|---|---|---|
| UL flame retardant rating | UL 94 | HB | |
| Burning wire flammability index | IEC 60695-2-12 | 850 °C | |
| IEC 60695-2-12 | 960 °C | ||
| Hot filament ignition temperature | IEC 60695-2-13 | 875 °C | |
| IEC 60695-2-13 | 875 °C |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Dart impact equipped with measuring instruments | ASTM D3763 | 70.0 J | |
| Unscented Izod Impact Strength 8 | ISO 180/1U | 无断裂 | |
| ISO 180/1U | 无断裂 | ||
| Impact strength of cantilever beam gap | ASTM D256 | 770 J/m | |
| ASTM D256 | 870 J/m | ||
| ISO 180/1A | 60 kJ/m² | ||
| ISO 180/1A | 70 kJ/m² | ||
| The impact strength of a simply supported beam without a notch is 7 | ISO 179/1eU | 无断裂 | |
| Impact strength of simply supported beam gap 7 | ISO 179/1eA | 70 kJ/m² | |
| The impact strength of a simply supported beam without a notch is 7 | ISO 179/1eU | 无断裂 | |
| Impact strength of simply supported beam gap 7 | ISO 179/1eA | 65 kJ/m² |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Bending stress | ISO 178 | 85.0 Mpa | |
| ASTM D790 | 92.0 Mpa | ||
| Flexural modulus | ASTM D790 | 2230 Mpa | |
| ISO 178 | 2250 Mpa | ||
| elongation | ISO 527-2/50 | 120 % | |
| ASTM D638 | 98 % | ||
| ISO 527-2/50 | 6.0 % | ||
| ASTM D638 | 6.0 % | ||
| tensile strength | ISO 527-2/50 | 60.0 Mpa | |
| ASTM D638 | 50.0 Mpa | ||
| ISO 527-2/50 | 57.0 Mpa | ||
| ASTM D638 | 55.0 Mpa | ||
| Tensile modulus | ISO 527-2/1 | 2150 Mpa | |
| ASTM D638 | 2020 Mpa |
| injection | Test Condition | Test Method | Test Result |
|---|---|---|---|
| screw speed | 40 到 70 rpm | ||
| Exhaust hole depth | 0.025 到 0.076 mm | ||
| Temperature | 70 到 95 °C | ||
| Back pressure | 0.300 到 0.700 Mpa | ||
| drying temperature | 120 °C | ||
| drying time | 3.0 到 4.0 hr | ||
| Suggested maximum moisture content | 0.020 % | ||
| Suggested injection volume | 40 到 60 % | ||
| Temperature at the rear of the barrel | 270 到 295 °C | ||
| Temperature in the middle of the barrel | 280 到 305 °C | ||
| Temperature at the front of the material cylinder | 295 到 315 °C | ||
| Spray nozzle temperature | 290 到 310 °C | ||
| Processing (melt) temperature | 295 到 315 °C |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| dielectric strength | ASTM D149 | 16 KV/mm | |
| Surface Resistivity | ASTM D257 | > 1.0E+15 ohms | |
| Volume resistivity | ASTM D257 | > 1.0E+15 ohms·cm | |
| dielectric constant | ASTM D150 | 2.68 | |
| ASTM D150 | 2.64 | ||
| Dissipation Factor | ASTM D150 | 1.2E-3 | |
| ASTM D150 | 9.3E-3 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| RTI | UL 746 | 125 °C | |
| RTI Imp | UL 746 | 120 °C | |
| RTI Elec | UL 746 | 130 °C | |
| ISO 11359-2 | 7.2E-5 cm/cm/°C | ||
| ASTM E831 | 7.5E-5 cm/cm/°C | ||
| Ball Pressure Test | IEC 60695-10-2 | 通过 | |
| ASTM E831 | 7.0E-5 cm/cm/°C | ||
| ISO 11359-2 | 7.2E-5 cm/cm/°C | ||
| vicat | ISO 306/B120 | 146 °C | |
| ASTM D152510, ISO 306/B5010 | 145 °C | ||
| Thermal deformation temperature under load | ISO 75-2/Ae | 128 °C | |
| ISO 75-2/Be | 140 °C | ||
| ASTM D648 | 124 °C | ||
| ASTM D648 | 139 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Contact Us
Get App
Top