PPS A310M TORAY JAPAN

Form：Granules | Grade：Injection grade

Properties:

Flame retardantGlass fiber reinforcedMineral reinforcementHigh rigidityhigh strengthHigh temperature resistan

Typical Applications:

Fiber grade

Supplier(1)

Product Description

Certificates(1)

Datasheet

Product Description

Typical Applications:	Fiber grade
Properties:	Flame retardant \| Glass fiber reinforced \| Mineral reinforcement \| High rigidity \| high strength \| High temperature resistan

Certificates

Technical Data Sheet

other	Test Condition	Test Method	Test Result	Test Unit
characteristic			高硬度
Color			本色.黑
impact performance	Test Condition	Test Method	Test Result	Test Unit
Impact strength of simply supported beam without notch	23°C	ISO 179	16	kJ/m²
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	0.36mm	UL 94	V-0
Basic Performance	Test Condition	Test Method	Test Result	Test Unit
Water absorption rate		ASTM D-570	0.02	%
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
bending strength		ASTM D-790	17.6	GPa
Shore hardness		ASTM D-785	123	洛氏
tensile strength		ASTM D-638	1.2	%
Friction coefficient	对钢	ASTM D-1894	0.30
tensile strength		ASTM D-638	140	Mpa
abrasion		ASTM D-1044	70	mg/1000回
Impact strength of cantilever beam gap	Unnotched23℃	ASTM D-256	20	KJ/m
Impact strength of cantilever beam gap	Impact strength of cantilever beam gap	Notched23℃	ASTM D-256	90	J/m
limiting pv value		东丽法	815	KJ/m
Elongation at Break		ASTM D-732	60
bending strength		ASTM D-790	200	Mpa
tensile strength	Yield,23°C	ISO 527-2	115	Mpa
Tensile strain	Break,23°C	ISO 527-2	0.80	%
Bending modulus	23°C	ISO 178	22000	Mpa
bending strength	23°C	ISO 178	200	Mpa
shear strength	23°C	JISK7214	60.0	Mpa
Friction coefficient			0.30
Taber abraser	1000Cycles	ISO 9352	70.0	mg
Charpy Notched Impact Strength		ASTM D256/ISO 179	16	kg·cm/cm(J/M)ft·lb/in
Elongation at Break		ASTM D638/ISO 527	0.8	%
tensile strength		ASTM D638/ISO 527	115	kg/cm²(MPa)[Lb/in²]
Rockwell hardness		ASTM D785	123
Charpy Notched Impact Strength		ASTM D256/ISO 179	7	kg·cm/cm(J/M)ft·lb/in
Bending modulus		ASTM D790/ISO 178	22	kg/cm²(MPa)[Lb/in²]
bending strength		ASTM D790/ISO 178	200	kg/cm²(MPa)[Lb/in²]
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Combustibility		UL -94	V-0
Melting temperature		DSC	278	°C
Linear coefficient of thermal expansion	垂重方向	ASTM D-696	2.4
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Flow	ASTM D-696	1.6
Hot deformation temperature	1.82MPa	ASTM D-648	>260	°C
Hot deformation temperature	Hot deformation temperature	1.8MPa,Unannealed	ISO 75-2/A	260	°C
Melting temperature		ISO 11357-3	278	°C
Linear coefficient of thermal expansion	MD	ISO 11359-2	1.9E-05	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	TD	ISO 11359-2	2E-05	cm/cm/°C
Combustibility (rate)		UL 94	V-0
Melting temperature			278	℃（℉）
Linear coefficient of thermal expansion		ASTM D696/ISO 11359	1.9	mm/mm.℃
Physical properties	Test Condition	Test Method	Test Result	Test Unit
	320℃,98MPa,1mm厚，Flow长	东丽法	90
Shrinkage rate	垂重方向	东丽法	0.55	%
	Shrinkage rate	Flow	东丽法	0.15	%
		Shrinkage rate	TD:3.00mm2	Internal Method	0.50	%
		Shrinkage rate	Shrinkage rate	MD:3.00mm4	Internal Method	0.20	%
Water absorption rate	23°C,24hr	ISO 62	0.020	%
density		ASTM D792/ISO 1183	2.06
Shrinkage rate		ASTM D955	0.5	%
Water absorption rate		ASTM D570/ISO 62	0.02	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Dielectric constant	10	ASTM D-150	5.8
Induced positive connection	10	ASTM D-150	0.002
Arc resistance	W电极	ASTM D-495	182	秒
Inherent resistance of volume		ASTM D-257	10	Ω.m
Dielectric strength		ASTM D-149	15	MV/m
Volume resistivity		IEC 60093	1E+16	ohms·cm
Dielectric strength		IEC 60243-1	22	KV/mm
Dielectric constant	23°C,1MHz	IEC 60250	5.00
Dissipation factor	23°C,1MHz	IEC 60250	2E-03
Dielectric constant		ASTM D150/IEC 60250	5
Volume resistivity		ASTM D257/IEC 60093	1014	Ω.cm
hardness	Test Condition	Test Method	Test Result	Test Unit
Rockwell hardness	R-Scale	ISO 2039-2	123
Supplementary Information	Test Condition	Test Method	Test Result	Test Unit
BarFlowLength	320°C,1.00mm	Internal Method	9.00	CM

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top