Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Shrinkage rate | | ASTMD955 | 2.0 % |
| Shrinkage rate | | ISO294-4 | 1.7to2.2 % |
| Shrinkage rate | | ISO294-4 | 1.7to2.2 % |
| density | | ISO1183 | 1.26 g/cm³ |
| melt mass-flow rate | | ASTMD1238 | 10to15 g/10min |
| melt mass-flow rate | | ISO1133 | 16 g/10min |
| density | | ASTMD792 | 1.25 g/cm³ |
| Specific volume | | ASTMD792 | 0.802 cm³/g |
| hardness | Test Condition | Test Method | Test Result |
|---|
| | ASTMD2240 | 72 |
| | ISO868 | 72 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL94 | HB |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|
| tear strength | | ASTMD1004 | 217.2 kN/m |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTMD638 | 635 MPa |
| Tensile modulus | | ISO527-2/1A/1 | 500 MPa |
| Flexural modulus | | ISO178 | 450 MPa |
| Bending stress | | ISO178 | 22.0 MPa |
| TaberAbrasion Resistance | | ASTMD4060 | 30.0 mg |
| RossFlex | | 内部方法 | >1.0E+6 Cycles |
| Tensile stress | Break | ISO527-2 | 40.0 MPa |
| Tensile stress | | ISO527-2 | 21.0 MPa |
| Tensile stress | | ISO527-2 | 27.0 MPa |
| Tensile stress | | ISO527-2 | 25.0 MPa |
| Tensile strain | Yield | ISO527-2/1A/50 | 19 % |
| elongation | | ASTMD638 | 300 % |
| Nominal tensile fracture strain | | ISO527-2/1A/50 | >50 % |
| Flexural modulus | | ISO178 | 2400 MPa |
| Tensile stress | Yield | ISO527-2/1A/50 | 28.0 MPa |
| tensile strength | | ASTMD638 | 29.2 MPa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | ISO179/1eA | 4.5 kJ/m² |
| Charpy Notched Impact Strength | | ISO179/1eA | 19 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO179/1eU | NoBreak |
| Impact strength of simply supported beam without notch | | ISO179/1eU | NoBreak |
| Impact strength of cantilever beam gap | | ISO180/1A | 4.8 kJ/m² |
| Impact strength of cantilever beam gap | | ISO180/1A | 16 kJ/m² |
| elastomer | Test Condition | Test Method | Test Result |
|---|
| tear strength | | ASTMD624 | 214 kN/m |
| TearStrength-Flow | | ISO34-1 | 190 kN/m |
| compression set | | ASTMD395 | <1.0 % |
| Basho elasticity | | 内部方法 | 40 % |
| Basho elasticity | | ASTMD2632 | 40 % |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| | IEC60250 | 3.70 |
| Dissipation Factor | | IEC60250 | 0.040 |
| CTI | | IEC60112 | >600 V |
| Surface Resistivity | | IEC60093 | 2E+17 ohms |
| dielectric strength | | IEC60243-1 | 28 kV/mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| | ISO75-2/B | 118 °C |
| Glass Transition Temperature | | ASTMD3418 | -23.3 °C |
| vicat | | ASTMD1525 | 204 °C |
| | ASTMD3418 | 214 °C |
| melting temperature | | ISO11357-3 | 215 °C |
| | ASTMD696 | 1.7E-04 cm/cm/°C |
| | ISO11359-2 | 1.4E-04 cm/cm/°C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare