PPO PX9406P-7001 SABIC INNOVATIVE SHANGHAI

130

Form：Granules | Grade：Injection grade

Properties:

Flame retardant

Typical Applications:

Electronic communication accessoriesElectronic communication accessoriesbuilding materialsProfile

Supplier(1)

Product Description

Certificates(0)

Datasheet

Alternative Model(2)

Product Description

Typical Applications:	Electronic communication accessories \| Electronic communication accessories \| building materials \| Profile
Properties:	Flame retardant

Certificates

No Data...

Technical Data Sheet

Filling analysis	Test Condition	Test Method	Test Result	Test Unit
Melt viscosity	280°C, 1500 sec^-1	ISO 11443	278	Pa·s
impact performance	Test Condition	Test Method	Test Result	Test Unit
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	9.0	kJ/m²
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	0.40 mm	UL 94	V-2
	UL flame retardant rating	0.75 mm	UL 94	V-0
	UL flame retardant rating	UL flame retardant rating	2.5 mm	UL 94	5VA
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
tensile strength	Yield	Internal Method	63.0	Mpa
tensile strength	tensile strength	Yield	ISO 527-2/50	73.0	Mpa
Tensile strain	Break	Internal Method	85	%
Tensile strain	Tensile strain	Break	ISO 527-2/50	4.5	%
Bending modulus	--	ASTM D790	2350	Mpa
Bending modulus	Bending modulus	--2	ISO 178	2600	Mpa
bending strength	--	ASTM D790	99.0	Mpa
bending strength	bending strength	--2,3	ISO 178	108	Mpa
injection	Test Condition	Test Method	Test Result	Test Unit
drying temperature			105 to 110	°C
drying time			3.0 to 4.0	hr
Suggested maximum moisture content			0.020	%
Suggested injection volume			30 to 70	%
Temperature at the rear of the barrel			245 to 295	°C
Temperature in the middle of the barrel			255 to 300	°C
Temperature at the front of the material cylinder			265 to 305	°C
Spray nozzle temperature			275 to 305	°C
Processing (melt) temperature			275 to 305	°C
Mold temperature			70 to 100	°C
Back pressure			0.300 to 0.700	Mpa
Screw speed			20 to 100	rpm
Exhaust hole depth			0.038 to 0.051	mm
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45 MPa, Unannealed, 6.40 mm	ASTM D648	136	°C
	Hot deformation temperature	1.8 MPa, Unannealed, 6.40 mm	ASTM D648	125	°C
	Hot deformation temperature	Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span5	ISO 75-2/Af	117	°C
Vicat softening temperature	--	ISO 306/A120	151	°C
Vicat softening temperature	Vicat softening temperature	--	ISO 306/B120	142	°C
Ball Pressure Test	125°C	IEC 60695-10-2	通过
Linear coefficient of thermal expansion	Flow : -30 to 30°C	TMA	7.0E-5	cm/cm/°C
	Linear coefficient of thermal expansion	Flow : -40 to 40°C	ISO 11359-2	6.6E-5	cm/cm/°C
	Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Across Flow : -40°C	ISO 11359-2	7.6E-5	cm/cm/°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
melt mass-flow rate	250°C/10.0 kg	ASTM D1238	3.9	g/10 min
Melt Volume Flow Rate (MVR)	280°C/10.0 kg	ISO 1133	27.0	cm3/10min
	Melt Volume Flow Rate (MVR)	280°C/5.0 kg	ISO 1133	10.0	cm3/10min
	Melt Volume Flow Rate (MVR)	Melt Volume Flow Rate (MVR)	300°C/5.0 kg	ISO 1133	23.0	cm3/10min
Shrinkage rate	3.20 mm，Flow	Internal Method	0.50 - 0.70	%
Water absorption rate	24 hr	ASTM D570	0.070	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Surface resistivity		ASTM D257	1.0E+16	ohms
Dielectric constant	60 Hz	ASTM D150	2.80
Dielectric constant	Dielectric constant	50 kHz	ASTM D150	2.80

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top