Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTM D1238 | 5.6 g/10min |
| melt mass-flow rate | | ISO 1133 | 18 g/10min |
| Shrinkage rate | | 内部方法 | 0.50-0.80 % |
| melt viscosity | | ASTM D3835 | 225 Pa·s |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 112 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | HB |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTM D638 | 2270 Mpa |
| Tensile modulus | | ISO 527-2/1 | 2370 Mpa |
| tensile strength | | ASTM D638 | 44.0 Mpa |
| tensile strength | | ISO 527-2/50 | 47.0 Mpa |
| tensile strength | | ASTM D638 | 33.0 Mpa |
| tensile strength | | ISO 527-2/50 | 35.0 Mpa |
| elongation | | ASTM D638 | 2.0 % |
| Tensile strain | | ISO 527-2/50 | 2.6 % |
| elongation | | ASTM D638 | 24 % |
| Tensile strain | | ISO 527-2/50 | 25 % |
| Flexural modulus | | ASTM D790 | 2300 Mpa |
| Flexural modulus | | ISO 178 | 2200 Mpa |
| bending strength | | ISO 178 | 70.0 Mpa |
| bending strength | | ASTM D790 | 70.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | ISO 179/1eA | 9.0 kJ/m² |
| Charpy Notched Impact Strength | | ISO 179/1eA | 26 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/1A | 8.0 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/1A | 22 kJ/m² |
| Dart impact | | ASTM D3763 | 30.0 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| High Voltage Arc Traceability Rate (HVTR) | | UL 746 | PLC 3 |
| Hot wire ignition (HWI) | | UL 746 | PLC 3 |
| arc resistance | | ASTM D495 | PLC6 |
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 0 |
| High arc combustion index (HAI) | | UL 746 | PLC 0 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| vicat | | ISO 306/B50 | 98.0 °C |
| vicat | | ISO 306/B120 | 100 °C |
| Linear coefficient of thermal expansion | | ASTME831 | 8.8E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTME831 | 8.8E-05 cm/cm/°C |
| RTI Elec | | UL 746 | 60.0 °C |
| RTI Imp | | UL 746 | 60.0 °C |
| RTI Str | | UL 746 | 60.0 °C |
| Heat distortion temperature | | ASTM D648 | 94.0 °C |
| Heat distortion temperature | | ASTM D648 | 80.0 °C |
| Heat distortion temperature | | ISO 75-2/Af | 81.0 °C |
| vicat | | ASTM D152510 | 99.0 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare