Technical Data Sheet
| other | Test Condition | Test Method | Test Result |
|---|
| characteristic | | | 30%玻纤增强 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | V-0 |
| UL flame retardant rating | | UL 94 | V-0 |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Impact strength of cantilever beam gap | | ASTM D256/ISO 179 | 25 kg·cm/cm(J/M)ft·lb/in |
| Impact strength of cantilever beam gap | | ASTM D256/ISO 179 | 20 kg·cm/cm(J/M)ft·lb/in |
| elongation at break | | ASTM D638/ISO 527 | 2.7 % |
| Tensile modulus | | ASTM D638/ISO 527 | 13500 kg/cm²(MPa)[Lb/in²] |
| tensile strength | | ASTM D638/ISO 527 | 165 kg/cm²(MPa)[Lb/in²] |
| Flexural modulus | | ASTM D790/ISO 178 | - kg/cm²(MPa)[Lb/in²] |
| bending strength | | ASTM D790/ISO 178 | 195 kg/cm²(MPa)[Lb/in²] |
| Tensile modulus | | ISO 527-2/1A/1 | 13000 Mpa |
| tensile strength | | ISO 527-2/1A/5 | 130 Mpa |
| Tensile strain | | ISO 527-2/1A/5 | 1.8 % |
| Flexural modulus | | ISO 178 | 12000 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 35 kJ/m² |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | ASTM D257/IEC 60093 | 1.00E+16 Ω |
| Volume resistivity | | ASTM D257/IEC 60093 | 1.00E+17 Ω.cm |
| Surface Resistivity | | IEC 60093 | >1.0E+16 ohms |
| Volume resistivity | | IEC 60093 | >1.0E+16 ohms·cm |
| dielectric strength | | IEC 60243-1 | 36 KV/mm |
| relative permittivity | | IEC 60250 | 4.00 |
| relative permittivity | | 内部方法 | 4.16 |
| Dissipation Factor | | IEC 60250 | 0.031 |
| Dissipation Factor | | 内部方法 | 5E-03 |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | PLC 3 |
| Physical properties | Test Condition | Test Method | Test Result |
|---|
| density | | ASTM D792/ISO 1183 | 1680 |
| Water absorption rate | | ASTM D570/ISO 62 | 0.002 % |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648/ISO 75 | - ℃（℉） |
| Heat distortion temperature | | ASTM D648/ISO 75 | 268 ℃（℉） |
| melting temperature | | | 335 ℃（℉） |
| Heat distortion temperature | | ISO 75-2/A | 265 °C |
| melting temperature | | ISO 11357-3 | 335 °C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 3E-06 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 7E-05 cm/cm/°C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices