ASA CR7500 BK1041 SABIC INNOVATIVE SHANGHAI

Form：Granules | Grade：Impact resistant grade

Properties:

Thermal stabilityAntistaticHigh mobility

Typical Applications:

Automotive ApplicationsElectrical applications

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Typical Applications:	Automotive Applications \| Electrical applications
Properties:	Thermal stability \| Antistatic \| High mobility

Certificates

No Data...

Technical Data Sheet

impact performance	Test Condition	Test Method	Test Result	Test Unit
Dart impact	23°C, Total Energy	ASTM D3763	30.0	J
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Tensile modulus	--2	ASTM D638	1970	Mpa
Tensile modulus	Tensile modulus	--	ISO 527-2/1	2040	Mpa
tensile strength	Yield3	ASTM D638	40.0	Mpa
	tensile strength	Yield	ISO 527-2/5	43.0	Mpa
		tensile strength	Break3	ASTM D638	33.0	Mpa
		tensile strength	tensile strength	Break	ISO 527-2/5	35.0	Mpa
elongation	Yield3	ASTM D638	3.6	%
	elongation	Yield	ISO 527-2/5	3.3	%
		elongation	Break3	ASTM D638	60	%
		elongation	elongation	Break	ISO 527-2/5	19	%
Bending modulus	50.0 mm Span4	ASTM D790	2170	Mpa
Bending modulus	Bending modulus	--5	ISO 178	2060	Mpa
bending strength	--5,6	ISO 178	64.0	Mpa
bending strength	bending strength	Yield, 50.0 mm Span4	ASTM D790	68.0	Mpa
injection	Test Condition	Test Method	Test Result	Test Unit
drying temperature			85 to 95	°C
drying time			3.0 to 4.0	hr
Suggested maximum moisture content			0.040	%
Suggested injection volume			40 to 80	%
Temperature at the rear of the barrel			230 to 250	°C
Temperature in the middle of the barrel			235 to 255	°C
Temperature at the front of the material cylinder			245 to 260	°C
Spray nozzle temperature			235 to 255	°C
Processing (melt) temperature			255 to 270	°C
Mold temperature			60 to 85	°C
Back pressure			0.300 to 1.00	Mpa
Screw speed			30 to 80	rpm
Exhaust hole depth			0.038 to 0.076	mm
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	1.8 MPa, Unannealed, 3.20 mm	ASTM D648	90.0	°C
	Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 100 mm Span9	ISO 75-2/Ae	88.0	°C
	Hot deformation temperature	Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span8	ISO 75-2/Af	89.0	°C
Vicat softening temperature	--	ASTM D152510	98.0	°C
	Vicat softening temperature	--	ISO 306/B50	102	°C
	Vicat softening temperature	Vicat softening temperature	--	ISO 306/B120	105	°C
Ball Pressure Test	98°C	IEC 60695-10-2	通过
Linear coefficient of thermal expansion	Flow : -40 to 40°C	ASTM E831	8.4E-5	cm/cm/°C
	Linear coefficient of thermal expansion	Across Flow : -40 to 40°C	ASTM E831	9.5E-5	cm/cm/°C
	Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Across Flow : -40°C	ISO 11359-2	9.5E-5	cm/cm/°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
melt mass-flow rate	220°C/10.0 kg	ASTM D1238	6.3	g/10 min
melt mass-flow rate	melt mass-flow rate	260°C/5.0 kg	ASTM D1238	11	g/10 min
Melt Volume Flow Rate (MVR)	220°C/10.0 kg	ISO 1133	6.00	cm3/10min
Melt Volume Flow Rate (MVR)	Melt Volume Flow Rate (MVR)	260°C/5.0 kg	ISO 1133	10.0	cm3/10min
Shrinkage rate	3.20 mm，Flow	Internal Method	0.50 - 0.80	%
Water absorption rate	Saturation, 23°C	ISO 62	0.50	%
Water absorption rate	Water absorption rate	Equilibrium, 23°C, 50% RH	ISO 62	0.20	%

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top