PA66 70G30L DUPONT GERMANY

Form：Granules | Grade：Enhanced level

Properties:

LubricityThermal stabilityHydrolysis resistance

Typical Applications:

Electrical applicationsAutomotive ApplicationsFitness equipmentelectrical equipment

Supplier(1)

Product Description

Certificates(1)

Datasheet

Product Description

Typical Applications:	Electrical applications \| Automotive Applications \| Fitness equipment \| electrical equipment
Properties:	Lubricity \| Thermal stability \| Hydrolysis resistance

Certificates

Technical Data Sheet

Filling analysis	Test Condition	Test Method	Test Result	Test Unit
Melt density			1.21	g/cm³
Specific Heat Capacity of Melt			2290	J/kg/°C
Thermal Conductivity of Melt			0.21	W/m/K
Emission of Organic Compounds		VDA 277	6.00	µgC/g
Odor		VDA 270	4.50
impact performance	Test Condition	Test Method	Test Result	Test Unit
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	60	kJ/m²
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	80	kJ/m²
flammability	Test Condition	Test Method	Test Result	Test Unit
Burning rate	1.00 mm	ISO 3795	24	mm/min
UL flame retardant rating		UL 94	HB
UL flame retardant rating	UL flame retardant rating		UL 94	HB
Extreme Oxygen Index		ISO 4589-2	24	%
FMVSS combustion rate		FMVSS 302	SE/B
Atomization	F-value (refraction)	ISO 6452	95	%
Atomization	Atomization	G-value (condensate)	ISO 6452	3.0E-4	g
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Tensile modulus		ISO 527-2	9800	Mpa
tensile strength	Break	ISO 527-2	195	Mpa
Tensile strain	Break	ISO 527-2	3.5	%
injection	Test Condition	Test Method	Test Result	Test Unit
drying temperature			80	°C
Drying time - hot air dryer			2.0 to 4.0	hr
Suggested maximum moisture content			0.20	%
Processing (melt) temperature			285 to 305	°C
Melt Temperature, Optimum			295	°C
Mold temperature			70 to 120	°C
Mold Temperature, Optimum			100	°C
Maintain pressure			50.0 to 100	Mpa
Maintain pressure	Maintain pressure	Drying Recommended		yes
Hold Pressure Time			3.00	s/mm
Maximum Screw Tangential Speed			12	m/min
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45 MPa, Unannealed	ISO 75-2/B	260	°C
Hot deformation temperature	Hot deformation temperature	1.8 MPa, Unannealed	ISO 75-2/A	253	°C
Glass transition temperature		ISO 11357-2	80.0	°C
Melting temperature		ISO 11357-3	262	°C
Linear coefficient of thermal expansion	Flow	ISO 11359-2	2.8E-5	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Across Flow	ISO 11359-2	9.5E-5	cm/cm/°C
Effective thermal diffusivity coefficient			6.85E-8	m²/s
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Shrinkage rate	横向Flow	ISO 294-4	1.1	%
Shrinkage rate	Shrinkage rate	Flow	ISO 294-4	0.30	%
Water absorption rate	Saturation, 23°C, 2.00 mm	ISO 62	6.9	%
Water absorption rate	Water absorption rate	Equilibrium, 23°C, 2.00 mm, 50% RH	ISO 62	2.0	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Surface resistivity		IEC 62631-3-2	--	ohms
Volume resistivity		IEC 62631-3-1	1.0E+11	ohms·m
Dissipation factor	100 Hz	IEC 62631-2-1	0.016
Dissipation factor	Dissipation factor	1 MHz	IEC 62631-2-1	0.016
Compared to the anti leakage trace index	3.00 mm	UL 746	PLC 0

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top