Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Melt volume flow rate | | ISO 1133 | 30.0 cm³/10min |
| Shrinkage rate | | ISO 294-4 | 0.80 % |
| Shrinkage rate | | ISO 294-4 | 0.10 % |
| Shrinkage rate | | ISO 294-4 | 0.20 % |
| Shrinkage rate | | ISO 294-4 | 0.10 % |
| Water absorption rate | | ISO 62 | 0.30 % |
| Water absorption rate | | ISO 62 | 0.10 % |
| | ISO 1628 | 80.0 ml/g |
| density | | ISO 1183 | 1.69 g/cm³ |
| Apparent density | | ISO 60 | 0.80 g/cm³ |
| hardness | Test Condition | Test Method | Test Result |
|---|
| | ISO 2039-1 | 250 MPa |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | HB |
| Burning wire flammability index | | IEC 60695-2-12 | 750 °C |
| Limiting Oxygen Index | | ISO 4589-2 | 21 % |
| UL flame retardant rating | | UL 94 | HB |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|
| electrolytic corrosion | | IEC 60426 | A1 |
| ISO Shortcut | | ISO 7792 | PBT+PET.GHLMR.09-160.GF45 |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 65 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 60 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/1A | <10 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/1A | <10 kJ/m² |
| Charpy Notched Impact Strength | | ISO 179/1eA | <10 kJ/m² |
| Charpy Notched Impact Strength | | ISO 179/1eA | <10 kJ/m² |
| Suspended wall beam without notch impact strength | | ISO 180/1U | 5560 kJ/m² |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Bending Strain | | | 2.1 % |
| Tensile modulus | | ISO 527-2/1 | 16000 MPa |
| tensile strength | | ISO 527-2/5 | 160 MPa |
| Tensile strain | | ISO 527-2/5 | 1.9 % |
| Tensile creep modulus | | ISO 899-1 | 16500 MPa |
| Tensile creep modulus | | ISO 899-1 | 15000 MPa |
| Flexural modulus | | ISO 178/A | 15500 MPa |
| bending strength | | ISO 178 | 260 MPa |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | IEC 60093 | >1.0E+15 ohms |
| Volume resistivity | | IEC 60093 | >1.0E+15 ohms·cm |
| dielectric strength | | IEC 60243-1 | 28 kV/mm |
| | IEC 60250 | 4.30 |
| | IEC 60250 | 4.20 |
| Dissipation Factor | | IEC 60250 | 2E-03 |
| Dissipation Factor | | IEC 60250 | 0.014 |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | PLC 2 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| BallPressure Test | | IEC 60695-10-2 | Pass |
| melting temperature | | ISO 11357-3 | 225to250 °C |
| | ISO 11359-2 | 2E-05 cm/cm/°C |
| | ISO 11359-2 | 8E-05 cm/cm/°C |
| TemperatureIndex | | IEC 60216 | 155 |
| Hot deformation temperature (HDT) | | ISO 75-2/B | 225 °C |
| Hot deformation temperature (HDT) | | ISO 75-2/A | 205 °C |
| Hot deformation temperature (HDT) | | ISO 75-2/C | 150 °C |
| vicat | | ISO 306/B120 | 210 °C |
| thermal conductivity | | ISO 8302 | 0.27 W/m/K |
| Half Interval | | IEC 60216 | 13.5 °C |
| Half Interval | | IEC 60216 | 10.2 °C |
| Half Interval | | IEC 60216 | 10.2 °C |
| TemperatureIndex | | IEC 60216 | 155 |
| TemperatureIndex | | IEC 60216 | 150 |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare