Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTM D1238 | 15 g/10 min |
| Melt volume flow rate | | ISO 1133 | 15.0 cm3/10min |
| Shrinkage rate | | 内部方法 | 0.50 - 0.80 % |
| Shrinkage rate | | 内部方法 | 0.40 - 0.60 % |
| Water absorption rate | | ISO 62 | 0.49 % |
| Water absorption rate | | ISO 62 | 0.15 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Shore hardness | | ASTM D2240 | 73 |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| refractive index | | ISO 489 | 1.539 |
| transmissivity | | ASTM D1003 | 88.0 % |
| Haze ratio | | ASTM D1003 | < 2.0 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| Burning wire flammability index | | IEC 60695-2-12 | 750 °C |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTM D638 | 1520 Mpa |
| Tensile modulus | | ISO 527-2/1 | 1600 Mpa |
| tensile strength | | ASTM D638 | 47.0 Mpa |
| tensile strength | | ISO 527-2/50 | 55.0 Mpa |
| tensile strength | | ASTM D638 | 46.0 Mpa |
| tensile strength | | ISO 527-2/50 | 54.0 Mpa |
| elongation | | ASTM D638 | 5.0 % |
| elongation | | ISO 527-2/50 | 5.0 % |
| elongation | | ASTM D638 | 150 % |
| elongation | | ISO 527-2/50 | > 200 % |
| Flexural modulus | | ASTM D790 | 1680 Mpa |
| Flexural modulus | | ISO 178 | 1700 Mpa |
| bending strength | | ISO 178 | 78.0 Mpa |
| bending strength | | ASTM D790 | 71.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Dart impact | | ASTM D3763 | 95.0 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | ASTM D257 | > 1.0E+15 ohms |
| Volume resistivity | | ASTM D257 | > 1.0E+15 ohms·cm |
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 0 |
| injection | Test Condition | Test Method | Test Result |
|---|
| drying temperature | | | 65 to 75 °C |
| drying time | | | 3.0 to 5.0 hr |
| Suggested maximum moisture content | | | 0.020 % |
| Suggested injection volume | | | 40 to 80 % |
| Temperature at the rear of the barrel | | | 240 to 250 °C |
| Temperature in the middle of the barrel | | | 240 to 260 °C |
| Temperature at the front of the material cylinder | | | 245 to 265 °C |
| Spray nozzle temperature | | | 245 to 265 °C |
| Processing (melt) temperature | | | 245 to 265 °C |
| Temperature | | | 45 to 60 °C |
| Back pressure | | | 0.200 to 0.500 Mpa |
| screw speed | | | 20 to 100 rpm |
| Exhaust hole depth | | | 0.013 to 0.020 mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648 | 79.0 °C |
| Heat distortion temperature | | ASTM D648 | 75.0 °C |
| Heat distortion temperature | | ISO 75-2/Ae | 80.0 °C |
| vicat | | ASTM D152510 | 96.0 °C |
| vicat | | ISO 306/B50 | 92.0 °C |
| ball-indentation hardness | | IEC 60695-10-2 | 通过 |
| Linear coefficient of thermal expansion | | ASTM E831 | 1.1E-4 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 9.0E-5 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTM E831 | 1.1E-4 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 1.1E-4 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 9.0E-5 cm/cm/°C |
| thermal conductivity | | ISO 8302 | 0.23 W/m/K |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices