Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| density | | ISO1183 | 1.42 g/cm³ |
| melt mass-flow rate | | ISO1133 | 15 g/10min |
| Melt volume flow rate | | ISO1133 | 13.0 cm3/10min |
| Shrinkage rate | | ISO294-4 | 1.9 % |
| Shrinkage rate | | ISO294-4 | 2.0 % |
| Water absorption rate | | ISO62 | 1.4 % |
| Water absorption rate | | ISO62 | 0.40 % |
| MediumDensity | | | 1.19 g/cm³ |
| ThermalConductivityofMelt | | | 0.24 W/m/K |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ISO2039-2 | 92 |
| Rockwell hardness | | ISO2039-2 | 120 |
| | ISO2039-1 | 192 Mpa |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | IEC60695-11-10,-20 | HB |
| UL flame retardant rating | | IEC60695-11-10,-20 | HB |
| Limiting Oxygen Index | | ISO4589-2 | 22 % |
| FMVSS flammability | | FMVSS302 | B |
| atomization | | ISO6452 | 90 % |
| atomization | | ISO6452 | 3.5E-04 g |
| Burning rate 3 | | ISO3795 | 20 mm/min |
| UL flame retardant rating | | UL94 | HB |
| UL flame retardant rating | | UL94 | HB |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|
| Emission | | VDA275 | <8.00 mg/kg |
| Emissions of Organic Compounds | | VDA277 | 3.10 µgC/g |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ISO527-2 | 3100 Mpa |
| Tensile stress | | ISO527-2 | 71.0 Mpa |
| Tensile strain | | ISO527-2 | 17 % |
| Nominal tensile fracture strain | | ISO527-2 | 30 % |
| TensileCreepModule | | ISO899-1 | 2800 Mpa |
| Tensile creep modulus | | ISO899-1 | 1600 Mpa |
| Flexural modulus | | ISO178 | 3000 Mpa |
| Bending stress | | ISO178 | 80.0 Mpa |
| Poisson's ratio | | ISO527 | 0.35 |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| | ISO180/1U | 250 kJ/m² |
| | ISO180/1U | 280 kJ/m² |
| Multi axis Instrumented Impact Energy | | ISO6603-2 | 3.00 J |
| Multi axis Instrumented Peak Impact Force | | ISO6603-2 | 2000 N |
| Charpy Notched Impact Strength | | ISO179/1eA | 8.0 kJ/m² |
| Charpy Notched Impact Strength | | ISO179/1eA | 9.0 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO179/1eU | 280 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO179/1eU | 320 kJ/m² |
| Impact strength of cantilever beam gap | | ISO180/1A | 8.0 kJ/m² |
| Impact strength of cantilever beam gap | | ISO180/1A | 9.0 kJ/m² |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | IEC60093 | 4E+14 ohms |
| Volume resistivity | | IEC60093 | 2E+14 ohms·cm |
| dielectric strength | | IEC60243-1 | 44 KV/mm |
| | IEC60250 | 3.80 |
| | IEC60250 | 3.80 |
| Dissipation Factor | | IEC60250 | 9E-03 |
| Dissipation Factor | | IEC60250 | 5.5E-03 |
| CTI | | IEC60112 | 600 V |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| | ISO75-2/B | 160 °C |
| | ISO75-2/A | 95.0 °C |
| vicat | | ISO306/B50 | 155 °C |
| BallPressure Test | | IEC60695-10-2 | Pass |
| melting temperature | | ISO11357-3 | 178 °C |
| | ISO11359-2 | 1E-04 cm/cm/°C |
| | ISO11359-2 | 9E-05 cm/cm/°C |
| | ISO11359-2 | 1E-04 cm/cm/°C |
| | ISO11359-2 | 9E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO11359-2 | 160 °C |
| Linear coefficient of thermal expansion | | ISO11359-2 | 30.0 min/mm |
| | ISO11359-2 | 9E-08 m²/s |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices