Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| Melt mass flow rate | 230°C/3.8 kg | ASTM D1238 | 5.6 | g/10 min |
| Melt mass flow rate | 220°C/10.0 kg | ISO 1133 | 18 | g/10 min |
| Shrinkage rate - flow | 3.20 mm | 内部方法 | 0.50 到 0.80 | % |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Rockwell hardness | R 级 | ASTM D785 | 112 | |
| Tensile modulus | -- 1 | ASTM D638 | 2270 | Mpa |
| Tensile modulus | -- | ISO 527-2/1 | 2370 | Mpa |
| tensile strength | 屈服 2 | ASTM D638 | 44.0 | Mpa |
| tensile strength | 屈服 | ISO 527-2/50 | 47.0 | Mpa |
| tensile strength | 断裂 2 | ASTM D638 | 33.0 | Mpa |
| tensile strength | 断裂 | ISO 527-2/50 | 35.0 | Mpa |
| elongation | 屈服 2 | ASTM D638 | 2.0 | % |
| elongation | 屈服 | ISO 527-2/50 | 2.6 | % |
| elongation | 断裂 2 | ASTM D638 | 24 | % |
| elongation | 断裂 | ISO 527-2/50 | 25 | % |
| Bending modulus | 50.0 mm 跨距 3 | ASTM D790 | 2300 | Mpa |
| Bending modulus | -- 4 | ISO 178 | 2200 | Mpa |
| bending strength | -- 4, 5 | ISO 178 | 70.0 | Mpa |
| bending strength | 屈服, 50.0 mm 跨距 3 | ASTM D790 | 70.0 | Mpa |
| Impact strength of simply supported beam gap | -30°C | ISO 179/1eA | 9.0 | kJ/m² |
| Impact strength of simply supported beam gap | 23°C | ISO 179/1eA | 26 | kJ/m² |
| Dart impact equipped with measuring instruments | 23°C, Total Energy | ASTM D3763 | 30.0 | J |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Hot deformation temperature | 0.45 MPa, 未退火, 3.20 mm | ASTM D648 | 94.0 | °C |
| Hot deformation temperature | 1.8 MPa, 未退火, 3.20 mm | ASTM D648 | 80.0 | °C |
| Hot deformation temperature | 1.8 MPa, 未退火, 4.00 mm, 64.0 mm 跨距 7 | ISO 75-2/Af | 81.0 | °C |
| vicat softening point | -- | | 99.0 | °C |
| vicat softening point | -- | ISO 306/B50 | 98.0 | °C |
| vicat softening point | -- | ISO 306/B120 | 100 | °C |
| Linear coefficient of thermal expansion | 流动 : -40 到 40°C | ASTM E831 | 8.8E-5 | cm/cm/°C |
| Linear coefficient of thermal expansion | 横向 : -40 到 40°C | ASTM E831 | 8.8E-5 | cm/cm/°C |
| RTI Elec | | UL 746 | 60.0 | °C |
| RTI Imp | | UL 746 | 60.0 | °C |
| RTI | | UL 746 | 60.0 | °C |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Arc resistance | | ASTM D495 | PLC 6 | |
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 0 | |
| High arc combustion index (HAI) | | UL 746 | PLC 0 | |
| High Voltage Arc Traceability Rate (HVTR) | | UL 746 | PLC 3 | |
| Hot wire ignition (HWI) | | UL 746 | PLC 3 | |
| Filling analysis | Test Condition | Test Method | Test Result | Unit |
|---|
| Melt viscosity | 240°C, 1000 sec^-1 | ASTM D3835 | 225 | Pa·s |
| injection | Test Condition | Test Method | Test Result | Unit |
|---|
| drying temperature | | | 80 到 95 | °C |
| drying time | | | 2.0 到 4.0 | hr |
| Suggested maximum moisture content | | | 0.10 | % |
| Suggested injection volume | | | 50 到 70 | % |
| Temperature at the rear of the barrel | | | 190 到 210 | °C |
| Temperature in the middle of the barrel | | | 205 到 225 | °C |
| Temperature at the front of the material cylinder | | | 215 到 240 | °C |
| Spray nozzle temperature | | | 220 到 260 | °C |
| Processing (melt) temperature | | | 220 到 260 | °C |
| Mold temperature | | | 50 到 70 | °C |
| Back pressure | | | 0.300 到 0.700 | Mpa |
| Screw speed | | | 30 到 60 | rpm |
| Exhaust hole depth | | | 0.038 到 0.051 | mm |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| UL flame retardant rating | 1.5 mm | UL 94 | HB | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices