Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Shrinkage rate | | ASTM D955 | 0.40 % |
| Shrinkage rate | | ASTM D955 | 0.80 % |
| Water absorption rate | | ASTM D570 | 0.21 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 125 |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| transmissivity | | ASTM D1003 | >35 % |
| transmissivity | | ASTM D1003 | >30 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | HB |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Flexural modulus | | ASTM D790 | 10300 Mpa |
| Flexural modulus | | ISO 178 | 10300 Mpa |
| bending strength | | ISO 178 | 326 Mpa |
| bending strength | | ASTM D790 | 317 Mpa |
| compressive strength | | ASTM D695 | 276 Mpa |
| shear strength | | ASTM D732 | 101 Mpa |
| Poisson's ratio | | | 7.58 0.41 |
| Tensile modulus | | ASTM D638 | 13100 Mpa |
| Tensile modulus | | ISO 527-2 | 12200 Mpa |
| tensile strength | | ISO 527-2 | 225 Mpa |
| tensile strength | | ASTM D638 | 221 Mpa |
| elongation | | ASTM D638 | 2.5 % |
| Tensile strain | | ISO 527-2 | 3.0 % |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 82 kJ/m² |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| arc resistance | | ASTM D495 | 140 sec |
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | V |
| Volume resistivity | | ASTM D257 | 1E+16 ohms·cm |
| dielectric strength | | ASTM D149 | 21 KV/mm |
| dielectric constant | | ASTM D150 | 4.40 |
| dielectric constant | | ASTM D150 | 4.20 |
| Dissipation Factor | | ASTM D150 | 5E-03 |
| Dissipation Factor | | ASTM D150 | 0.017 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648 | 297 °C |
| Heat distortion temperature | | ASTM D648 | 285 °C |
| Heat distortion temperature | | ISO 75-2/Af | 277 °C |
| Continuous use temperature | | ASTM D3045 | 164 °C |
| Continuous use temperature | | ASTM D3045 | 185 °C |
| melting temperature | | ASTM D3418 | 310 °C |
| melting temperature | | ISO 11357-3 | 310 °C |
| Linear coefficient of thermal expansion | | ASTME831 | 2.3E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTME831 | 1.4E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTME831 | 5.9E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTME831 | 1.3E-04 cm/cm/°C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices