Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| density | | ISO 1183 | 1.15 g/cm³ |
| melt mass-flow rate | | ISO 1133 | 19 g/10min |
| Melt volume flow rate | | ISO 1133 | 18.0 cm3/10min |
| Shrinkage rate | | ISO 294-4 | 0.85 % |
| Shrinkage rate | | ISO 294-4 | 0.85 % |
| Water absorption rate | | ISO 62 | 0.30 % |
| Water absorption rate | | ISO 62 | 0.12 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| ball-indentation hardness | | ISO 2039-1 | 127 Mpa |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| refractive index | | ISO 489 | 1.573 |
| transmissivity | | ISO 13468-2 | 89.0 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | HB |
| Burning wire flammability index | | IEC 60695-2-12 | 850 °C |
| Limiting Oxygen Index | | ISO 4589-2 | 26 % |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|
| electrolytic corrosion | | IEC 60426 | A1 |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile strain | | ISO 527-2/50 | 6.6 % |
| Nominal tensile fracture strain | | ISO 527-2/50 | >50 % |
| Flexural modulus | | ISO 178 | 2450 Mpa |
| bending strength | | ISO 178 | 108 Mpa |
| Tensile modulus | | ISO 527-2/1 | 2450 Mpa |
| tensile strength | | ISO 527-2/50 | 74.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam without notch | | ISO 179/1eU | NoBreak |
| Impact strength of simply supported beam without notch | | ISO 179/1eU | NoBreak |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Dissipation Factor | | IEC 60250 | 1E-03 |
| Dissipation Factor | | IEC 60250 | 9E-03 |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | V |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | V |
| Surface Resistivity | | IEC 60093 | 1E+16 ohms |
| Volume resistivity | | IEC 60093 | 1E+17 ohms·cm |
| dielectric strength | | IEC 60243-1 | 35 KV/mm |
| relative permittivity | | IEC 60250 | 2.90 |
| relative permittivity | | IEC 60250 | 2.80 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ISO 75-2/B | 172 °C |
| Heat distortion temperature | | ISO 75-2/A | 157 °C |
| vicat | | ISO 306/B120 | 182 °C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 6.5E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 6.5E-05 cm/cm/°C |
| RTI Elec | | UL 746 | 150 °C |
| RTI Imp | | UL 746 | 130 °C |
| RTI Str | | UL 746 | 150 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices