Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| density | | ASTM D-792 | 无水｜1.59 |
| density | | ASTM D-792 | 1.3%水｜- |
| density | | g/cm³ | 1.59 -- |
| Shrinkage rate | | % | 0.60-0.90 -- |
| Shrinkage rate | | % | 0.20-0.50 -- |
| Water absorption rate | | % | 0.60 -- |
| Water absorption rate | | % | 4.0 -- |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | | 121 -- |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | | V-0 -- |
| Basic performance | Test Condition | Test Method | Test Result |
|---|
| Water absorption rate | | ASTM D-570 | 无水｜0.4 % |
| Water absorption rate | | ASTM D-570 | 1.3%水｜- % |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Impact strength of cantilever beam gap | | | 无水｜65 kg.cm/cm |
| Impact strength of cantilever beam gap | | | 1.3%水｜70 kg.cm/cm |
| tensile strength | | ASTM D-638 | 无水｜1640 kg/cm2 |
| tensile strength | | ASTM D-638 | 1.3%水｜1350 kg/cm2 |
| elongation at break | | ASTM D-638 | 无水｜5 % |
| elongation at break | | ASTM D-638 | 1.3%水｜5 % |
| bending strength | | ASTM D-790 | 无水｜2490 kg/cm2 |
| bending strength | | ASTM D-790 | 1.3%水｜2000 kg/cm2 |
| Flexural modulus | | ASTM D-790 | 无水｜93200 kg/cm2 |
| Flexural modulus | | ASTM D-790 | 1.3%水｜65000 kg/cm2 |
| Tensile strain | | % | 2.5 -- |
| Tensile strain | | % | 3.0 3.0 |
| Tensile strain | | % | 4.5 -- |
| Flexural modulus | | MPa | 10200 -- |
| Flexural modulus | | MPa | 9300 6500 |
| Flexural modulus | | MPa | 5500 -- |
| bending strength | | MPa | 275 -- |
| bending strength | | | 250 MPa |
| bending strength | | MPa | 150 -- |
| Taber abraser | | mg | 26.0 -- |
| tensile strength | | MPa | 190 -- |
| tensile strength | | | 165 MPa |
| tensile strength | | MPa | 110 -- |
| Other performance | Test Condition | Test Method | Test Result |
|---|
| filler content | | | 无水｜30 wt% |
| filler content | | | 1.3%水｜- wt% |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | kJ/m² | 7.0 -- |
| Charpy Notched Impact Strength | | kJ/m² | 9.5 14 |
| Impact strength of simply supported beam without notch | | kJ/m² | 65 70 |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Volume resistivity | | ASTM D-257 | 1.3%水｜8×1013 Ω.cm |
| dielectric strength | | ASTM D-149 | 无水｜38 KV/mm |
| dielectric strength | | ASTM D-149 | 1.3%水｜33 KV/mm |
| Compared to the Leakage Traceability Index (CTI) | | UL 746 | 无水｜200 V |
| Compared to the Leakage Traceability Index (CTI) | | UL 746 | 1.3%水｜- V |
| Dissipation Factor | | ASTM D-150 | 无水｜0.003-0.009 |
| Dissipation Factor | | ASTM D-150 | 1.3%水｜- |
| arc resistance | | ASTM D-495 | 无水｜70-80 S |
| arc resistance | | ASTM D-495 | 1.3%水｜- S |
| Volume resistivity | | ASTM D-257 | 无水｜8×1014 Ω.cm |
| Volume resistivity | | ohms·cm | 1E+15 1E+13 |
| dielectric strength | | kV/mm | 38 33 |
| dielectric constant | | | 4.00 -- |
| dielectric constant | | | 0.0100 -- |
| arc resistance | | sec | 70.0 -- |
| Compared to the Leakage Tracking Index (CTI) | | V | -- |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Linear coefficient of thermal expansion | | ASTM D-696 | 无水｜2 10-5cm/cm.℃ |
| Linear coefficient of thermal expansion | | ASTM D-696 | 1.3%水｜- |
| Heat distortion temperature | | ASTM D-648 | 无水｜251 °C |
| Heat distortion temperature | | ASTM D-648 | 1.3%水｜- °C |
| melting temperature | | 差示扫描测热计DSC法 | 无水｜265 °C |
| UL-94 flame retardant grade | | UL 94 | 无水｜V-0 |
| UL-94 flame retardant grade | | UL 94 | 1.3%水｜- |
| Heat distortion temperature | | °C | 251 -- |
| melting temperature | | °C | 265 -- |
| Linear coefficient of thermal expansion | | cm/cm/°C | 2E-05 -- |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices