PA66 101L DUPONT SINGAPORE

226

Form：Granules | Grade：Injection grade

Properties:

Processability

Typical Applications:

Industrial machineryHousehold goodsConsumer goods sector

Supplier(1)

Product Description

Certificates(1)

Datasheet

Alternative(13)

Product Description

Typical Applications:	Industrial machinery \| Household goods \| Consumer goods sector
Properties:	Processability

Certificates

Technical Data Sheet

Filling analysis	Test Condition	Test Method	Test Result	Test Unit
Melt density			0.970	g/cm³
Top out temperature			190	°C
Specific Heat Capacity of Melt			2790	J/kg/°C
Thermal Conductivity of Melt			0.16	W/m/K
Emission of Organic Compounds		VDA 277	5.00	µgC/g
Odor		VDA 270	3.00
impact performance	Test Condition	Test Method	Test Result	Test Unit
Charpy Notched Impact Strength	-30°C	ISO 179/1eA	4.5	kJ/m²
Charpy Notched Impact Strength	Charpy Notched Impact Strength	23°C	ISO 179/1eA	5.5	kJ/m²
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	400 kJ/m²
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	无断裂
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating		UL 94	V-2
UL flame retardant rating	UL flame retardant rating		UL 94	V-2
Extreme Oxygen Index		ISO 4589-2	28	%
FMVSS combustion rate		FMVSS 302	DNI
Atomization	F-value (refraction)	ISO 6452	99	%
Atomization	Atomization	G-value (condensate)	ISO 6452	1.0E-4	g
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Tensile modulus		ISO 527-2	3100	Mpa
tensile strength	Yield	ISO 527-2	82.0	Mpa
Tensile strain	Yield	ISO 527-2	4.5	%
Nominal tensile fracture strain		ISO 527-2	25	%
Tensile creep modulus	1 hr	ISO 899-1	--	Mpa
Tensile creep modulus	Tensile creep modulus	1000 hr	ISO 899-1	--	Mpa
Bending modulus		ISO 178	2800	Mpa
injection	Test Condition	Test Method	Test Result	Test Unit
drying temperature			80	°C
Drying time - hot air dryer			2.0 to 4.0	hr
Suggested maximum moisture content			0.20	%
Processing (melt) temperature			280 to 300	°C
Melt Temperature, Optimum			290	°C
Mold temperature			50 to 90	°C
Mold Temperature, Optimum			70	°C
Maintain pressure			50.0 to 100	Mpa
Maintain pressure	Maintain pressure	Drying Recommended		yes
Hold Pressure Time			4.00	s/mm
Maximum Screw Tangential Speed			24	m/min
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45 MPa, Unannealed	ISO 75-2/B	190	°C
Hot deformation temperature	Hot deformation temperature	1.8 MPa, Unannealed	ISO 75-2/A	70.0	°C
Glass transition temperature		ISO 11357-2	60.0	°C
Vicat softening temperature		ISO 306/B50	240	°C
Melting temperature		ISO 11357-3	262	°C
Linear coefficient of thermal expansion	Flow	ISO 11359-2	1.0E-4	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Across Flow	ISO 11359-2	1.1E-4	cm/cm/°C
Effective thermal diffusivity coefficient			5.00E-8	m²/s
Physical properties	Test Condition	Test Method	Test Result	Test Unit
density		ISO 1183	1.14	g/cm³
Shrinkage rate	横向Flow	ISO 294-4	1.4	%
Shrinkage rate	Shrinkage rate	Flow	ISO 294-4	1.4	%
Water absorption rate	Saturation, 23°C, 2.00 mm	ISO 62	8.5	%
Water absorption rate	Water absorption rate	Equilibrium, 23°C, 2.00 mm, 50% RH	ISO 62	2.6	%
Stickiness	96% H2SO4	ISO 307	150	cm³/g
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Surface resistivity		IEC 62631-3-2	--	ohms
Volume resistivity		IEC 62631-3-1	1.0E+12	ohms·m
Dielectric strength		IEC 60243-1	32	KV/mm
Relative permittivity	1 MHz	IEC 62631-2-1	3.50
Relative permittivity	Relative permittivity	100 Hz	IEC 62631-2-1	3.80
Dissipation factor	100 Hz	IEC 62631-2-1	8.0E-3
Dissipation factor	Dissipation factor	1 MHz	IEC 62631-2-1	0.018
Compared to the anti leakage trace index		IEC 60112	PLC 0
hardness	Test Condition	Test Method	Test Result	Test Unit
Rockwell hardness	M -Sale	ISO 2039-2	79
Rockwell hardness	Rockwell hardness	R -Sale	ISO 2039-2	121
film	Test Condition	Test Method	Test Result	Test Unit
elongation	Yield， MD	ISO 527-3	4.5	%

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top