PBT S620F20 DuPont, European Union

Form：Granules | Grade：Injection grade

Supplier(1)

Product Description

Certificates(1)

Datasheet

Product Description

Certificates

Technical Data Sheet

Filling analysis	Test Condition	Test Method	Test Result	Test Unit
Melt density			1.11	g/cm³
Top out temperature			170	°C
SpecificHeatCapacity of Melt			2100	J/kg/°C
ThermalConductivityofMelt			0.21	W/m/K
impact performance	Test Condition	Test Method	Test Result	Test Unit
Suspended wall beam without notch impact strength	23°C	ISO 180/1U	140	kJ/m²
Suspended wall beam without notch impact strength	Suspended wall beam without notch impact strength	-30°C	ISO 180/1U	70	kJ/m²
Impact strength of cantilever beam gap	23°C	ISO 180/1A	4.0	kJ/m²
Impact strength of cantilever beam gap	Impact strength of cantilever beam gap	-30°C	ISO 180/1A	5.0	kJ/m²
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	无断裂
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Charpy Notched Impact Strength	23°C	ISO 179/1eA	4.5	kJ/m²
Charpy Notched Impact Strength	Charpy Notched Impact Strength	-30°C	ISO 179/1eA	3.5	kJ/m²
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	0.8mm	UL 94,IEC60695-11-10,-20	HB
UL flame retardant rating	UL flame retardant rating	1.5mm	UL 94,IEC60695-11-10,-20	HB
Extreme Oxygen Index		ISO 4589-2	22	%
FMVSS flammability		FMVSS302	SE/NBR
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Tensile strain	Yield	ISO 527-2	8.0	%
tensile strength	Yield	ISO 527-2	59.0	Mpa
Tensile modulus		ISO 527-2	2600	Mpa
bending strength		ISO 178	88.0	Mpa
Tensile creep modulus	1000hr	ISO 899-1	1800	Mpa
Tensile creep modulus	Tensile creep modulus	1hr	ISO 899-1	2600	Mpa
Nominal tensile fracture strain		ISO 527-2	30	%
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	1.8MPa,Unannealed	ISO 75-2/A	60.0	°C
	Hot deformation temperature	1.8MPa,Annealed	ISO 75-2/A	60.0	°C
		Hot deformation temperature	0.45MPa,Annealed	ISO 75-2/B	180	°C
		Hot deformation temperature	Hot deformation temperature	0.45MPa,Unannealed	ISO 75-2/B	145	°C
Vicat softening temperature		ISO 306/B50	175	°C
Melting temperature		ISO 11357-3	225	°C
Crystallization peak temperature		ISO 11357-3	192	°C
Linear coefficient of thermal expansion	MD	ISO 11359-2	1.3E-04	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	TD	ISO 11359-2	1.3E-04	cm/cm/°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Stickiness		ISO 307	130	cm³/g
Water absorption rate	Equilibrium,23°C,2.00mm,50%RH	ISO 62	0.20	%
Water absorption rate	Water absorption rate	Saturation,23°C,2.00mm	ISO 62	0.40	%
Shrinkage rate	MD	ISO 294-4	1.7	%
Shrinkage rate	Shrinkage rate	TD	ISO 294-4	1.6	%
melt mass-flow rate	250°C/2.16kg	ISO 1133	19	g/10min
density		ISO 1183	1.31	g/cm³
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Volume resistivity		IEC 60093	>1.0E+15	ohms·cm
Dielectric strength		IEC 60243-1	26	KV/mm
Relative permittivity	100Hz	IEC 60250	3.80
Relative permittivity	Relative permittivity	1MHz	IEC 60250	3.20
Dissipation factor	100Hz	IEC 60250	2E-03
Dissipation factor	Dissipation factor	1MHz	IEC 60250	0.020
Compared to the anti leakage trace index		IEC 60112	PLC 0

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top