Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PC EXL1433T SABIC INNOVATIVE NANSHA
LEXAN™
Automotive sector、Electronic and Electrical、Plastic bag
Middle flow、High ductility at low tem、Short molding cycle
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL1433T |
|---|---|---|---|
| 23°C | ISO 180/1A | 65 kJ/m² | |
| Dart impact | 23°C,TotalEnergy | ASTM D3763 | 82.4 J |
| Impact strength of simply supported beam without notch | -30°C | ISO 179/1eU | 无断裂 |
| 23°C | ISO 179/1eU | 无断裂 | |
| -30°C | ASTM D256 | 800 J/m | |
| Charpy Notched Impact Strength | 23°C | ISO 179/1eA | 70 kJ/m² |
| Dart impact | -30°C,TotalEnergy | ASTM D3763 | 85.0 J |
| Charpy Notched Impact Strength | -30°C | ISO 179/1eA | 50 kJ/m² |
| 23°C | ASTM D256 | 890 J/m | |
| Impact strength of cantilever beam gap | -30°C | ISO 180/1A | 45 kJ/m² |
| Suspended wall beam without notch impact strength | 23°C | ISO 180/1U | 无断裂 |
| -30°C | ISO 180/1A | 45 kJ/m² | |
| Impact strength of cantilever beam gap | 23°C | ISO 180/1A | 65 kJ/m² |
| Suspended wall beam without notch impact strength | -30°C | ISO 180/1U | 无断裂 |
| hardness | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL1433T |
|---|---|---|---|
| Rockwell hardness | L计秤 | ISO 2039-2 | 90 |
| L计秤 | ASTM D785 | 90 |
| Mechanical properties | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL1433T |
|---|---|---|---|
| Tensile modulus | ISO 527-2/1 | 2350 Mpa | |
| yield | ASTM D638 | 58.0 Mpa | |
| elongation | 屈服 | ASTM D638 | 5.8 % |
| Yield, 50.0mm span | ASTM D790 | 94.3 Mpa | |
| yield | ISO 527-2/50 | 57.9 Mpa | |
| fracture | ISO 527-2/50 | 61.5 Mpa | |
| tensile strength | 断裂 | ISO 527-2/50 | 61.5 Mpa |
| Flexural modulus | 50.0mm跨距 | ASTM D790 | 2220 Mpa |
| tensile strength | 屈服 | ISO 527-2/50 | 57.9 Mpa |
| elongation | 断裂 | ASTM D638 | 130 % |
| fracture | ISO 527-2/50 | 120 % | |
| yield | ISO 527-2/50 | 5.5 % | |
| Flexural modulus | ISO 178 | 2150 Mpa | |
| --8 | ISO 178 | 90.2 Mpa | |
| yield | ASTM D638 | 5.8 % | |
| tensile strength | 断裂 | ASTM D638 | 64.1 Mpa |
| fracture | ASTM D638 | 64.1 Mpa | |
| Tensile strain | 屈服 | ISO 527-2/50 | 5.5 % |
| Tensile modulus | ASTM D638 | 2220 Mpa | |
| bending strength | 屈服,50.0mm跨距 | ASTM D790 | 94.3 Mpa |
| fracture | ASTM D638 | 130 % | |
| bending strength | ISO 178 | 90.2 Mpa | |
| tensile strength | 屈服 | ASTM D638 | 58.0 Mpa |
| 50.0mm span | ASTM D790 | 2220 Mpa | |
| Tensile strain | 断裂 | ISO 527-2/50 | 120 % |
| --1 | ASTM D638 | 2220 Mpa | |
| --7 | ISO 178 | 2150 Mpa |
| Electrical performance | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL1433T |
|---|---|---|---|
| Volume resistivity | ASTM D257 | >1.0E+15 ohms·cm | |
| Surface Resistivity | ASTM D257 | >1.0E+15 ohms |
| optical performance | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL1433T |
|---|---|---|---|
| Haze ratio | 2540µm | ASTM D1003 | 3.0 % |
| transmissivity | 2540µm | ASTM D1003 | 82.0 % |
| flammability | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL1433T |
|---|---|---|---|
| Burning wire flammability index | 3.0mm | IEC 60695-2-12 | 960 °C |
| Hot filament ignition temperature | 0.800mm | IEC 60695-2-13 | 825 °C |
| UL flame retardant rating | 2.5mm | UL 94 | V-2 |
| 3.0mm | UL 94 | V-2 | |
| Hot filament ignition temperature | 3.00mm | IEC 60695-2-13 | 825 °C |
| 3.0mm | IEC 60695-2-13 | 825 °C | |
| UL flame retardant rating | 2.50mm | UL 94 | V-2 |
| Burning wire flammability index | 3.00mm | IEC 60695-2-12 | 960 °C |
| Hot filament ignition temperature | 0.8mm | IEC 60695-2-13 | 825 °C |
| physical property | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL1433T |
|---|---|---|---|
| Shrinkage rate | MD：3.20mm | 内部方法 | 0.40-0.80 % |
| MD:3.20mm | 内部方法 | 0.40-0.80 % | |
| Melt volume flow rate | 300°C/1.2kg | ISO 1133 | 9.50 cm3/10min |
| Shrinkage rate | TD：3.20mm | 内部方法 | 0.40-0.80 % |
| Water absorption rate | 平衡,23°C,50%RH | ISO 62 | 0.093 % |
| 饱和,23°C | ISO 62 | 0.12 % | |
| Shrinkage rate | TD:3.20mm | 内部方法 | 0.40-0.80 % |
| melt mass-flow rate | 300°C/1.2kg | ASTM D1238 | 10 g/10min |
| Thermal performance | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL1433T |
|---|---|---|---|
| Horizontal: 23 to 80 ° C | 横向, 23到80℃ | ISO 11359-2 | 7.9E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | MD：-40到95°C | ASTME831 | 7.2E-05 cm/cm/°C |
| Flow: -40 to 95 ° C | -40到95℃ | ASTME831 | 7.2E-05 cm/cm/°C |
| vicat | ASTM D152510 | 141 °C | |
| RTI Str | UL 746 | 130 °C | |
| RTI | UL 746 | 130 °C | |
| vicat | -- | ISO 306/B120 | 142 °C |
| Flow: 23 to 80 ° C | 23到80℃ | ISO 11359-2 | 7.2E-05 cm/cm/°C |
| Horizontal: -40 to 95 ° C | 横向, -40到95℃ | ASTME831 | 7.9E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | TD：-40to95°C | ASTME831 | 7.9E-05 cm/cm/°C |
| vicat | -- | ISO 306/B50 | 141 °C |
| Heat distortion temperature | 1.8MPa,Unannealed,64.0mmSpan，HDT | ISO 75-2/Af | 119 °C |
| Linear coefficient of thermal expansion | MD：23到80°C | ISO 11359-2 | 7.2E-05 cm/cm/°C |
| 1.8MPa, Unanealed, 64.0mm span | ISO 75-2/Af | 119 °C | |
| 1.8MPa, Unanealed, 3.20mm | ASTM D648 | 124 °C | |
| Heat distortion temperature | 1.8MPa,未退火,3.20mm，HDT | ASTM D648 | 124 °C |
| Linear coefficient of thermal expansion | TD：23to80°C | ISO 11359-2 | 7.9E-05 cm/cm/°C |
| ball-indentation hardness | 125°C | IEC 60695-10-2 | Pass |
| RTI Elec | UL 746 | 130 °C |
Contact Us
Get App
Top