Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
Polyester, TS Plenco 01586 (Injection) Plastics Engineering Co.
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | Plastics Engineering Co./Plenco 01586 (Injection) |
|---|---|---|---|
| Charpy Notched Impact Strength | ASTM D256 | 35.1 J/m | |
| Impact strength of cantilever beam gap | ASTM D256 | 42 J/m |
| hardness | Test Condition | Test Method | Plastics Engineering Co./Plenco 01586 (Injection) |
|---|---|---|---|
| Rockwell hardness | E计秤 | ASTM D785 | 54 |
| Electrical performance | Test Condition | Test Method | Plastics Engineering Co./Plenco 01586 (Injection) |
|---|---|---|---|
| dielectric strength | --3 | ASTM D149 | 13 kV/mm |
| Volume resistivity | ASTM D257 | 1.9E+15 ohms·cm | |
| Dissipation Factor | 1MHz | ASTM D150 | 0.017 |
| dielectric constant | 1MHz | ASTM D150 | 4.40 |
| dielectric strength | --4 | ASTM D149 | 11 kV/mm |
| Compared to the Leakage Tracking Index (CTI) | CTI | UL 746 | PLC 0 |
| arc resistance | ASTM D495 | 189 sec |
| Mechanical properties | Test Condition | Test Method | Plastics Engineering Co./Plenco 01586 (Injection) |
|---|---|---|---|
| elongation | 断裂 | ASTM D638 | 1.1 % |
| tensile strength | ASTM D638 | 64.0 MPa | |
| compressive strength | ASTM D695 | 119 MPa | |
| Tensile modulus | ASTM D638 | 11700 MPa | |
| Flexural modulus | ASTM D790 | 10300 MPa | |
| bending strength | ASTM D790 | 101 MPa |
| flammability | Test Condition | Test Method | Plastics Engineering Co./Plenco 01586 (Injection) |
|---|---|---|---|
| UL flame retardant rating | 1.0mm | UL 94 | V-0 |
| Limiting Oxygen Index | ASTM D2863 | 41 % |
| physical property | Test Condition | Test Method | Plastics Engineering Co./Plenco 01586 (Injection) |
|---|---|---|---|
| Shrinkage rate | MD | ASTM D955 | 0.37 % |
| Water absorption rate | 24hr | ASTM D570 | 0.060 % |
| Apparent density | ASTM D1895 | 0.89 g/cm³ | |
| density | ASTM D792 | 1.89 g/cm³ |
| Thermal performance | Test Condition | Test Method | Plastics Engineering Co./Plenco 01586 (Injection) |
|---|---|---|---|
| Heat distortion temperature | 1.8MPa,未退火，HDT | ASTM D648 | 253 °C |
| Continuous use temperature | ASTM D794 | 217 °C | |
| Linear coefficient of thermal expansion | MD | ASTME831 | 8.6E-05 cm/cm/°C |
| thermal conductivity | 100°C | ASTMC177 | 0.87 W/m/K |
Contact Us
Get App
Top