Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PPA HTNFR52G45NHLW DUPONT USA

Zytel®

household electrical appliances,Automotive interior parts,electrical equipment

Dimensional stability,Low water absorption,Heat aging,high strength,High rigidity

Plastic Datasheets

thermal performance	Test Condition	Test Method	DUPONT USA/HTNFR52G45NHLW
Hot deformation temperature	1.8 MPa, Unannealed	ISO 75-2/A	284 °C
Linear coefficient of thermal expansion	Across Flow : 55 to 160°C	ISO 11359-2	8.0E-5 cm/cm/°C
		Flow : -40 to 23°C	ISO 11359-2	1.3E-5 cm/cm/°C
		Across Flow	ISO 11359-2	5.0E-5 cm/cm/°C
		Flow	ISO 11359-2	1.5E-5 cm/cm/°C
		Flow : 55 to 160°C	ISO 11359-2	1.4E-5 cm/cm/°C
		Across Flow : -40 to 23°C	ISO 11359-2	4.3E-5 cm/cm/°C
Melting temperature		ISO 11357-3	310 °C
RTI Elec	0.75 mm	UL 746	140 °C
		1.5 mm	UL 746	140 °C
		3.0 mm	UL 746	140 °C
		0.40 mm	UL 746	140 °C

mechanical properties	Test Condition	Test Method	DUPONT USA/HTNFR52G45NHLW
Bending modulus		ISO 178	15100 Mpa
bending strength		ISO 178	249 Mpa
Tensile modulus		ISO 527-2	15500 Mpa
Tensile strain	Break	ISO 527-2	1.7 %
tensile strength	Break	ISO 527-2	167 Mpa

Electrical performance	Test Condition	Test Method	DUPONT USA/HTNFR52G45NHLW
Compared to the anti leakage trace index		IEC 60112	PLC 0
Dielectric strength		IEC 60243-1	40 KV/mm
Dissipation factor	1 MHz	IEC 62631-2-1	0.012
Dissipation factor		100 Hz	IEC 62631-2-1	6.0E-3
Relative permittivity	1 MHz	IEC 62631-2-1	4.40
Relative permittivity		100 Hz	IEC 62631-2-1	4.70
Volume resistivity		IEC 62631-3-1	> 1.0E+13 ohms·m

Physical properties	Test Condition	Test Method	DUPONT USA/HTNFR52G45NHLW
Shrinkage rate	横向Flow	ISO 294-4	0.60 %
Shrinkage rate		Flow	ISO 294-4	0.20 %

impact performance	Test Condition	Test Method	DUPONT USA/HTNFR52G45NHLW
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	45 kJ/m²
Impact strength of simply supported beam without notch		23°C	ISO 179/1eU	48 kJ/m²

flammability	Test Condition	Test Method	DUPONT USA/HTNFR52G45NHLW
Burning wire flammability index	0.75 mm	IEC 60695-2-12	960 °C
		3.0 mm	IEC 60695-2-12	960 °C
		1.5 mm	IEC 60695-2-12	960 °C
		0.40 mm	IEC 60695-2-12	960 °C
Hot filament ignition temperature	1.5 mm	IEC 60695-2-13	750 °C
		3.0 mm	IEC 60695-2-13	800 °C
		0.40 mm	IEC 60695-2-13	700 °C
		0.75 mm	IEC 60695-2-13	750 °C
UL flame retardant rating		UL 94	V-0

injection	Test Method	DUPONT USA/HTNFR52G45NHLW
drying temperature		100 °C
Drying time - hot air dryer		6.0 to 8.0 hr
Mold temperature		90 to 130 °C
Mold temperature	Drying Recommended		yes
Processing (melt) temperature		320 to 325 °C
Suggested maximum moisture content		0.10 %

Get App

Top