PC 1414T RD4D227X PC vs. - Plastic Material Properties Comparison Chart at Plas.com

injection	Test Condition	Test Method	SABIC INNOVATIVE NANSHA/1414T RD4D227X
Back pressure			0.300 to 0.700 Mpa
Temperature at the front of the material cylinder			295 to 315 °C
Screw speed			40 to 70 rpm
Mold temperature			70 to 95 °C
Processing (melt) temperature			295 to 315 °C
Suggested injection volume			40 to 60 %
Suggested maximum moisture content			0.020 %
Spray nozzle temperature			290 to 310 °C
Exhaust hole depth			0.025 to 0.076 mm
drying temperature			120 °C
Temperature in the middle of the barrel			280 to 305 °C
drying time			3.0 to 4.0 hr
Temperature at the rear of the barrel			215 to 295 °C
Physical properties	Test Condition	Test Method	SABIC INNOVATIVE NANSHA/1414T RD4D227X
Shrinkage rate	Across FlowFlow : 3.20 mm	Internal Method	0.40 - 0.80 %
Water absorption rate	Saturation, 23°C	ISO 62	0.12 %
Melt Volume Flow Rate (MVR)	300°C/1.2 kg	ISO 1133	9.00 cm3/10min
Shrinkage rate	Flow : 3.20 mm	Internal Method	0.40 - 0.80 %
Water absorption rate	Equilibrium, 23°C, 50% RH	ISO 62	0.090 %
Shrinkage rate	Flow 2	Internal Method	0.40 - 0.80 %
melt mass-flow rate	300°C/1.2 kg	ASTM D1238	10 g/10 min
mechanical properties	Test Condition	Test Method	SABIC INNOVATIVE NANSHA/1414T RD4D227X
Bending modulus	50.0 mm Span5	ASTM D790	2220 Mpa
bending strength	Yield, 50.0 mm Span5	ASTM D790	85.0 Mpa
elongation	Break	ISO 527-2/50	110 %
		Yield4	ASTM D638	5.8 %
		Yield	ISO 527-2/50	5.4 %
		Break4	ASTM D638	84 %
tensile strength	Break	ISO 527-2/50	54.0 Mpa
bending strength	--6,7	ISO 178	89.0 Mpa
tensile strength	Yield4	ASTM D638	59.0 Mpa
tensile strength		Yield	ISO 527-2/50	57.0 Mpa
Tensile modulus	--3	ASTM D638	2240 Mpa
Tensile modulus		--	ISO 527-2/1	2300 Mpa
Bending modulus	--6	ISO 178	2150 Mpa
tensile strength	Break4	ASTM D638	51.0 Mpa
thermal performance	Test Condition	Test Method	SABIC INNOVATIVE NANSHA/1414T RD4D227X
Vicat softening temperature	--	ASTM D152511	138 °C
Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span10	ISO 75-2/Af	116 °C
Linear coefficient of thermal expansion	Flow : 23 to 80°C	ISO 11359-2	6.7E-5 cm/cm/°C
		Across Flow : 23 to 80°C	ISO 11359-2	8.0E-5 cm/cm/°C
		Flow : -40 to 95°C	ASTM E831	6.7E-5 cm/cm/°C
Hot deformation temperature	1.8 MPa, Unannealed, 3.20 mm	ASTM D648	122 °C
Vicat softening temperature	--	ISO 306/B120	142 °C
Linear coefficient of thermal expansion	Across Flow : -40 to 95°C	ASTM E831	8.0E-5 cm/cm/°C
Ball Pressure Test	123 to 127°C	IEC 60695-10-2	通过
impact performance	Test Condition	Test Method	SABIC INNOVATIVE NANSHA/1414T RD4D227X
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Suspended wall beam without notch impact strength	23°C	ISO 180/1U	无断裂
Charpy Notched Impact Strength	-30°C	ISO 179/1eA	60 kJ/m²
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	无断裂
Dart impact	23°C, Total Energy	ASTM D3763	76.0 J
Charpy Notched Impact Strength	23°C	ISO 179/1eA	70 kJ/m²
Suspended wall beam without notch impact strength	-30°C	ISO 180/1U	无断裂

Get App

Top