Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PA6 CM1007 TORAY JAPAN

Amilan®

Electrical appliances

Low viscosity,High mobility

Plastic Datasheets

hardness	Test Condition	Test Method	TORAY JAPAN/CM1007
Rockwell hardness	R-Sale,80°C		80 --
Rockwell hardness		R-Sale,23°C		119

Basic Performance	Test Condition	Test Method	TORAY JAPAN/CM1007
Water absorption rate	23℃，24hr	ASTM D-570	3.5%水｜- %

thermal performance	Test Condition	Test Method	TORAY JAPAN/CM1007
Hot deformation temperature	4.6kg/cm2	ASTM D-695	3.5%水｜- °C
Hot deformation temperature		0.45MPa,Unannealed	°C	182 --
Linear coefficient of thermal expansion		ASTM D-696	无水｜8 ×10-5cm/cm/℃
Linear coefficient of thermal expansion		MD	cm/cm/°C	8E-05 --
Melting temperature		°C	225 --
				225 ℃（℉）
			差示扫描测热计DSC	225 °C
specific heat		J/kg/°C	1900 --
specific heat				3.5%水｜- Cal/g·℃
thermal conductivity			3.5%水｜- Kcal/m·hr·℃
thermal conductivity			W/m/K	0.25 --
UL-94 flame retardant grade		UL 94	3.5%水｜-

mechanical properties	Test Condition	Test Method	TORAY JAPAN/CM1007
Bending modulus	80℃	ASTM D-790	3.5%水｜3000 kg/cm2
		-40℃	ASTM D-790	3.5%水｜37000 kg/cm2
		-40°C	MPa	3800 3600
		23℃	ASTM D-790	3.5%水｜8000 kg/cm2
		80°C	MPa	700 300
		23°C		2800 MPa
bending strength	80°C	MPa	40.0 25.0
		80℃	ASTM D-790	3.5%水｜250 kg/cm2
		23°C	MPa	110 40.0
		-40°C		135 MPa
			ASTM D790/ISO 178	3.8 kg/cm²(MPa)[Lb/in²]
		23℃	ASTM D-790	3.5%水｜400 kg/cm2
		-40℃	ASTM D-790	3.5%水｜1300 kg/cm2
compressive strength	23℃	ASTM D-695	3.5%水｜- kg/cm2
Compressive stress	23°C	MPa	80.0 --
Elongation at Break	23℃	ASTM D-638	3.5%水｜< 200 %
Friction coefficient vs. Metal			0.15to0.20 --
Impact strength of cantilever beam gap	V-Notched1/2，23℃		3.5%水｜40 kg.cm/cm
Rockwell hardness	80℃	ASTM D-785	3.5%水｜- R-标度
			ASTM D785	80
		23℃	ASTM D-785	3.5%水｜88 R-标度
shear strength	23°C	MPa	70.0 65.0
Shear strength	23℃	ASTM D-732	3.5%水｜650 kg/cm2
Taber abraser	1000Cycles	mg	3.00to4.00 --
Tensile strain	Yield,23°C	%	2.0 --
Tensile strain		Break,23°C	%	35
tensile strength	-40℃，Yield	ASTM D-638	3.5%水｜1000 kg/cm2
		-40°C		110 MPa
		23℃，Yield	ASTM D-638	3.5%水｜350 kg/cm2
		80℃，Yield	ASTM D-638	3.5%水｜200 kg/cm2
		80°C	MPa	25.0 20.0
		23°C	MPa	80.0 35.0
		23℃，Break		3.5%水｜- kg/cm2

Electrical performance	Test Condition	Test Method	TORAY JAPAN/CM1007
Arc resistance		sec	120 --
Arc resistance		1/8	ASTM D-495	3.5%水｜- 秒
Compared to the anti leakage trace index	CTI	V	PLC 0
Compared to the Leakage Traceability Index (CTI)		UL 746	3.5%水｜- V
Dielectric constant	106Hz	ASTM D-150	3.5%水｜-
		103Hz	ASTM D-150	3.5%水｜-
		23°C,50Hz		4.10 9.00
		23°C,1kHz		3.90 8.00
		50Hz	ASTM D-150	3.5%水｜-
		23°C,1MHz		3.40 4.50
Dielectric strength	1/8	ASTM D-149	3.5%水｜- KV/mm
Dielectric strength			kV/mm	20 --
Dissipation factor	23°C,50Hz		0.070 0.10
		50Hz	ASTM D-150	3.5%水｜-
		23°C,1kHz		0.060 0.11
		103Hz	ASTM D-150	0.06｜-
		106Hz	ASTM D-150	3.5%水｜-
		23°C,1MHz		0.030 0.13
Volume resistivity		ohms·cm	1.0E+14-1.0E+15 1.0E+11到1.0E+12
			ASTM D257/IEC 60093	10^12-13 Ω.cm
			ASTM D-257	3.5%水｜1011-1012 Ω.cm

Physical properties	Test Condition	Test Method	TORAY JAPAN/CM1007
density		ASTM D792/ISO 1183	1.13
Shrinkage rate	MD：1.00mm3	%	0.50-1.0 --
Shrinkage rate		MD：3.00mm4	%	1.0-1.6 --
Taber abraser	1000g,CS-17	ASTM D-1044	3.5%水｜- mg/1000次
Water absorption rate	Saturation,23°C	%	11 --
		23°C,24hr	%	1.8 --
			ASTM D570/ISO 62	1.8 %

impact performance	Test Condition	Test Method	TORAY JAPAN/CM1007
Impact strength of simply supported beam without notch	-40°C		无断裂 --
Impact strength of simply supported beam without notch		23°C		无断裂 --

flammability	Test Condition	Test Method	TORAY JAPAN/CM1007
UL flame retardant rating	0.79mm		V-2 --

Get App

Top