Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
SPS SP140 IDEMITSU JAPAN
XAREC™
Household daily necessiti、Electrical applications
High temperature resistan、Glass fiber reinforced
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | IDEMITSU JAPAN/SP140 |
|---|---|---|---|
| Charpy Notched Impact Strength | 23°C | ISO 179 | 10 kJ/m² |
| Suspended wall beam without notch impact strength | 23°C | ISO 180 | 29 kJ/m² |
| Impact strength of cantilever beam gap | 23°C | ISO 180 | 10 kJ/m² |
| Impact strength of simply supported beam without notch | 23°C | ISO 179 | 33 kJ/m² |
| Mechanical properties | Test Condition | Test Method | IDEMITSU JAPAN/SP140 |
|---|---|---|---|
| Tensile modulus | ISO 527-2 | 6500 Mpa | |
| bending strength | ISO 178 | 120 Mpa | |
| Tensile strain | 断裂 | ISO 527-2 | 2.5 % |
| Flexural modulus | ISO 178 | 6100 Mpa | |
| tensile strength | 断裂 | ISO 527-2 | 75.0 Mpa |
| Electrical performance | Test Condition | Test Method | IDEMITSU JAPAN/SP140 |
|---|---|---|---|
| Compared to the Leakage Tracking Index (CTI) | IEC 60112 | PLC 0 | |
| Dissipation Factor | 1 MHz | IEC 60250 | < 1.0E-3 |
| Volume resistivity | IEC 60093 | > 1.0E+16 ohms·cm | |
| dielectric strength | ASTM D149 | 50 KV/mm | |
| arc resistance | ASTM D495 | PLC 6 | |
| dielectric constant | 1 MHz | IEC 60250 | 3.10 |
| flammability | Test Condition | Test Method | IDEMITSU JAPAN/SP140 |
|---|---|---|---|
| UL flame retardant rating | 1.5 mm | UL 94 | HB |
| physical property | Test Condition | Test Method | IDEMITSU JAPAN/SP140 |
|---|---|---|---|
| Water absorption rate | 平衡, 23°C, 50% RH | ISO 62 | 0.010 % |
| Shrinkage rate | 横向流量 | 内部方法 | 0.30 - 0.70 % |
| 流量 | 内部方法 | 0.20 - 0.50 % | |
| density | ISO 1183 | 1.31 g/cm³ |
| Thermal performance | Test Condition | Test Method | IDEMITSU JAPAN/SP140 |
|---|---|---|---|
| Heat distortion temperature | 0.45 MPa, 未退火，HDT | ISO 75-2/B | 255 °C |
| Linear coefficient of thermal expansion | 流动 : -30 到 30°C | TMA | 3.3E-5 cm/cm/°C |
| Heat distortion temperature | 1.8 MPa, 未退火，HDT | ISO 75-2/A | 175 °C |
| Linear coefficient of thermal expansion | 横向 : -30 到 30°C | TMA | 7.1E-5 cm/cm/°C |
| RTI Imp | UL 746 | 50.0 °C | |
| RTI | UL 746 | 50.0 °C | |
| RTI Elec | UL 746 | 50.0 °C |
| injection | Test Condition | Test Method | IDEMITSU JAPAN/SP140 |
|---|---|---|---|
| drying time | 3.0 to 5.0 hr | ||
| Processing (melt) temperature | 280 to 310 °C | ||
| drying temperature | 120 °C | ||
| Temperature | 130 to 155 °C |
Contact Us
Get App
Top