plas

Log In | Sign Up

Categories

Plastic Raw Materials

Modified Plastics

Plastic Additives

Color Masterbatch

Plastic Datasheets

Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PEI HU1010-1H1000 SABIC INNOVATIVE US

ULTEM™

Medical devices,Medical and nursing supplies

Middle flow,Biocompatibility,Steam sterilization

--

--

--

--

--

--

--

--

--

--

--

--

--

--

--

Plastic Datasheets

hardness	Test Condition	Test Method	SABIC INNOVATIVE US/HU1010-1H1000
Rockwell hardness	M-Scale	ASTM D785	109

thermal performance	Test Condition	Test Method	SABIC INNOVATIVE US/HU1010-1H1000
Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span9	ISO 75-2/Af	193 °C
		0.45 MPa, Unannealed, 6.40 mm	ASTM D648	207 °C
		1.8 MPa, Unannealed, 6.40 mm	ASTM D648	198 °C
Linear coefficient of thermal expansion	Flow : -20 to 150°C	ASTM E831	5.6E-5 cm/cm/°C
		Across Flow : -40°C	ISO 11359-2	5.0E-5 cm/cm/°C
		Flow : -40 to 40°C	ISO 11359-2	5.0E-5 cm/cm/°C
		Across Flow : -40 to 40°C	ASTM E831	5.0E-5 cm/cm/°C
RTI		UL 746	170 °C
RTI Elec		UL 746	170 °C
RTI Imp		UL 746	170 °C
thermal conductivity		ASTM C177	0.22 W/m/K
Vicat softening temperature	--	ISO 306/B120	212 °C
		--	ISO 306/B50	211 °C
		--	ASTM D152510	218 °C

mechanical properties	Test Condition	Test Method	SABIC INNOVATIVE US/HU1010-1H1000
Bending modulus	--6	ISO 178	3300 Mpa
		100 mm Span5	ASTM D790	3510 Mpa
		50.0 mm Span4	ASTM D790	3420 Mpa
bending strength	Yield, 50.0 mm Span4	ASTM D790	174 Mpa
		--6,7	ISO 178	160 Mpa
		Yield, 100 mm Span5	ASTM D790	165 Mpa
elongation	Break	ISO 527-2/5	60 %
		Yield3	ASTM D638	7.0 %
		Yield	ISO 527-2/5	6.0 %
		Break3	ASTM D638	60 %
Taber abraser	1000 Cycles, 1000 g, CS-17 Wheel	ASTM D1044	10.0 mg
Tensile modulus	--2	ASTM D638	3580 Mpa
Tensile modulus		--	ISO 527-2/1	3200 Mpa
tensile strength	Yield	ISO 527-2/5	105 Mpa
		Break3	ASTM D638	105 Mpa
		Yield3	ASTM D638	110 Mpa

Electrical performance	Test Condition	Test Method	SABIC INNOVATIVE US/HU1010-1H1000
Arc resistance		ASTM D495	PLC 5
Compared to the anti leakage trace index		UL 746	PLC 4
Dielectric constant	1 kHz	ASTM D150	3.15
Dielectric strength	1.60 mm, in Air	ASTM D149	33 KV/mm
Dielectric strength		1.60 mm, in Oil	ASTM D149	28 KV/mm
Dissipation factor	2.45 GHz	ASTM D150	2.5E-3
Dissipation factor		1 kHz	ASTM D150	1.3E-3
High arc combustion index		UL 746	PLC 3
High voltage arc tracing rate		UL 746	PLC 2
Hot wire ignition		UL 746	PLC 1
Volume resistivity		ASTM D257	1.0E+17 ohms·cm

Physical properties	Test Condition	Test Method	SABIC INNOVATIVE US/HU1010-1H1000
melt mass-flow rate	337°C/6.6 kg	ASTM D1238	18 g/10 min
Melt Volume Flow Rate (MVR)	360°C/5.0 kg	ISO 1133	25.0 cm3/10min
Shrinkage rate	3.20 mm，Flow	Internal Method	0.50 - 0.70 %
Water absorption rate	Equilibrium, 23°C	ASTM D570	1.3 %
		Saturation, 23°C	ISO 62	1.3 %
		Equilibrium, 23°C, 50% RH	ISO 62	0.70 %

impact performance	Test Condition	Test Method	SABIC INNOVATIVE US/HU1010-1H1000
Dart impact	23°C	ASTM D3029	33.0 J
Dart impact		23°C, Total Energy	ASTM D3763	33.0 J
Reverse notch impact	3.20 mm	ASTM D256	1200 J/m
Suspended wall beam without notch impact strength	23°C	ASTM D4812	1300 J/m

flammability	Test Condition	Test Method	SABIC INNOVATIVE US/HU1010-1H1000
Extreme Oxygen Index		ASTM D2863	44 %
UL flame retardant rating	0.71 mm	UL 94	V-2
		3.0 mm	UL 94	5VA
		0.75 mm	UL 94	V-0

injection	Test Condition	Test Method	SABIC INNOVATIVE US/HU1010-1H1000
Back pressure			0.300 to 0.700 Mpa
drying temperature			150 °C
drying time			4.0 to 6.0 hr
Exhaust hole depth			0.025 to 0.076 mm
Mold temperature			135 to 165 °C
Processing (melt) temperature			350 to 400 °C
Screw speed			40 to 70 rpm
Spray nozzle temperature			345 to 400 °C
Suggested injection volume			40 to 60 %
Suggested maximum moisture content			0.020 %
Temperature at the front of the material cylinder			345 to 400 °C
Temperature at the rear of the barrel			330 to 400 °C
Temperature in the middle of the barrel			340 to 400 °C

Contact Us

Get App

Top