Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates

DAP Synres-Almoco DAP 5562 Synres-Almoco BV
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
Impact resistance | Test Condition | Test Method | Synres-Almoco BV/Synres-Almoco DAP 5562 |
---|---|---|---|
Impact strength of simply supported beam without notch | 注塑 | ISO 179/1eU | 7.0to10 kJ/m² |
Charpy Notched Impact Strength | 注塑 | ISO 179/1eA | 3.5to4.5 kJ/m² |
Mechanical properties | Test Condition | Test Method | Synres-Almoco BV/Synres-Almoco DAP 5562 |
---|---|---|---|
bending strength | 注塑 | ISO 178 | 120to160 MPa |
Flexural modulus | 注塑 | ISO 178 | 11000to14000 MPa |
compression stress | ISO 604 | 150to200 MPa | |
tensile strength | 注塑 | ISO 527-2 | 80.0to90.0 MPa |
Tensile modulus | 注塑 | ISO 527-2 | 10000to14000 MPa |
Electrical performance | Test Condition | Test Method | Synres-Almoco BV/Synres-Almoco DAP 5562 |
---|---|---|---|
Compared to the Leakage Tracking Index (CTI) | IEC 60112 | PLC 1 | |
dielectric strength | IEC 60243-1 | 15to20 kV/mm | |
Volume resistivity | IEC 60093 | 1.0E+14到1.0E+15 ohms·cm | |
Dissipation Factor | 100Hz | IEC 60250 | 0.010to0.030 |
relative permittivity | 100Hz | IEC 60250 | 4.505.00 |
arc resistance | ASTM D495 | PLC 4 | |
relative permittivity | 1MHz | IEC 60250 | 4.004.50 |
Surface Resistivity | IEC 60093 | 1.0E+14到1.0E+15 ohms | |
Dissipation Factor | 1MHz | IEC 60250 | 0.010to0.030 |
flammability | Test Condition | Test Method | Synres-Almoco BV/Synres-Almoco DAP 5562 |
---|---|---|---|
Hot filament ignition temperature | IEC 60695-2-13 | 875 °C | |
UL flame retardant rating | 0.70mm | UL 94 | V-0 |
Burning wire flammability index | IEC 60695-2-12 | 960 °C |
physical property | Test Condition | Test Method | Synres-Almoco BV/Synres-Almoco DAP 5562 |
---|---|---|---|
Shrinkage rate | ISO 2577 | <0.050 % | |
Water absorption rate | 23°C,24hr | ISO 62 | <0.20 % |
Apparent density | ISO 60 | 0.75to0.90 g/cm³ | |
Shrinkage rate | MD3 | ISO 2577 | 0.15to0.45 % |
density | ISO 1183 | 1.80to2.00 g/cm³ |
Thermal performance | Test Condition | Test Method | Synres-Almoco BV/Synres-Almoco DAP 5562 |
---|---|---|---|
Heat distortion temperature | 1.8MPa,未退火,HDT | ISO 75-2/A | >200 °C |
Linear coefficient of thermal expansion | MD:50到100°C | ISO 11359-2 | 5.0E-6到1.0E-5 cm/cm/°C |
Heat distortion temperature | 8.0MPa,未退火,HDT | ISO 75-2/C | 130to150 °C |
thermal conductivity | ASTME1461 | 0.90to1.1 W/m/K |
Contact Us
Get App
Top