Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates

PC GN-3610L TEIJIN JAPAN
PANLITE®
machine,Mechanical components
High rigidity,Glass fiber reinforced
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
thermal performance | Test Condition | Test Method | TEIJIN JAPAN/GN-3610L |
---|---|---|---|
Hot deformation temperature | 0.45MPa,Unannealed | ISO 75-2/B | 143 °C |
HDT | ASTM D648/ISO 75 | 143 ℃(℉) | |
1.8MPa,Unannealed | ISO 75-2/A | 140 °C | |
Linear coefficient of thermal expansion | TD | ISO 11359-2 | 6E-05 cm/cm/°C |
ASTM D696/ISO 11359 | 0.000060 mm/mm.℃ | ||
MD | ISO 11359-2 | 4E-05 cm/cm/°C | |
RTI Elec | 1.5mm | UL 746 | 80.0 °C |
RTI Imp | 1.5mm | UL 746 | 80.0 °C |
RTI Str | 1.5mm | UL 746 | 80.0 °C |
Vicat softening temperature | ASTM D1525/ISO R306 | 146 ℃(℉) | |
ISO 306/B50 | 146 °C |
mechanical properties | Test Condition | Test Method | TEIJIN JAPAN/GN-3610L |
---|---|---|---|
Bending modulus | ISO 178 | 3600 Mpa | |
ASTM D790/ISO 178 | 3600 kg/cm²(MPa)[Lb/in²] | ||
bending strength | ASTM D790/ISO 178 | 115 kg/cm²(MPa)[Lb/in²] | |
ISO 178 | 115 Mpa | ||
Elongation at Break | ASTM D638/ISO 527 | 2.0 % | |
Tensile modulus | ISO 527-2/1 | 3800 Mpa | |
ASTM D638/ISO 527 | 3800 kg/cm²(MPa)[Lb/in²] | ||
Tensile strain | Break | ISO 527-2/5 | 2.0 % |
tensile strength | Break | ISO 527-2/5 | 70.0 Mpa |
ASTM D638/ISO 527 | 70.0 kg/cm²(MPa)[Lb/in²] |
Electrical performance | Test Condition | Test Method | TEIJIN JAPAN/GN-3610L |
---|---|---|---|
Compared to the anti leakage trace index | IEC 60112 | PLC 3 | |
Dielectric constant | ASTM D150/IEC 60250 | 3.20 | |
1MHz | IEC 60250 | 3.20 | |
100Hz | IEC 60250 | 3.20 | |
Dielectric loss | ASTM D150/IEC 60250 | 0.0090 | |
Dielectric strength | IEC 60243-1 | 35 KV/mm | |
Dissipation factor | 1MHz | IEC 60250 | 9E-03 |
100Hz | IEC 60250 | 1E-03 | |
Surface resistivity | ASTM D257/IEC 60093 | 1.0E+15 Ω | |
IEC 60093 | >1.0E+15 ohms | ||
Volume resistivity | IEC 60093 | >1.0E+15 ohms·cm | |
ASTM D257/IEC 60093 | 1.0E+15 Ω.cm |
other | Test Condition | Test Method | TEIJIN JAPAN/GN-3610L |
---|---|---|---|
remarks | 以上加工数据.为参考值.以生产厂商设备的实际状况而进行调整。 |
Physical properties | Test Condition | Test Method | TEIJIN JAPAN/GN-3610L |
---|---|---|---|
Shrinkage rate | ASTM D955 | 0.40-0.60 % | |
MD:4.00mm | Internal Method | 0.30-0.50 % | |
TD:4.00mm | Internal Method | 0.40-0.60 % | |
Water absorption rate | 23°C,24hr | ISO 62 | 0.16 % |
ASTM D570/ISO 62 | 0.16 % |
impact performance | Test Condition | Test Method | TEIJIN JAPAN/GN-3610L |
---|---|---|---|
Impact strength of simply supported beam without notch | ISO 179 | 45 kJ/m² |
flammability | Test Condition | Test Method | TEIJIN JAPAN/GN-3610L |
---|---|---|---|
Burning wire flammability index | 3.0mm | IEC 60695-2-12 | 960 °C |
1.6mm | IEC 60695-2-12 | 960 °C | |
1.0mm | IEC 60695-2-12 | 960 °C | |
Hot filament ignition temperature | 3.0mm | IEC 60695-2-13 | 850 °C |
1.0mm | IEC 60695-2-13 | 825 °C | |
1.6mm | IEC 60695-2-13 | 850 °C | |
UL flame retardant rating | 1.0mm | UL 94 | V-1 |
1.6mm | UL 94 | V-0 | |
0.40mm | UL 94 | V-2 |