Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PBT/PET T7331 LANXESS GERMANY
Pocan®
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | LANXESS GERMANY/T7331 |
|---|---|---|---|
| Suspended wall beam without notch impact strength | -30°C | ISO 180/1U | 55 kJ/m² |
| 23°C | ISO 180/1U | 55 kJ/m² | |
| Impact strength of simply supported beam without notch | 23°C | ISO 179/1eU | 65 kJ/m² |
| -30°C | ISO 179/1eU | 55 kJ/m² |
| Supplementary Information | Test Condition | Test Method | LANXESS GERMANY/T7331 |
|---|---|---|---|
| electrolytic corrosion | IEC 60426 | A1 | |
| ISO Shortcut | ISO 7792 | PBT+PET.GHLMR.09-100.GF30 |
| hardness | Test Condition | Test Method | LANXESS GERMANY/T7331 |
|---|---|---|---|
| ball-indentation hardness | ISO 2039-1 | 200 Mpa |
| film | Test Condition | Test Method | LANXESS GERMANY/T7331 |
|---|---|---|---|
| Thin film puncture strength | ISO 6603-2 | 650 N | |
| ISO 6603-2 | 2.10 J |
| Electrical performance | Test Condition | Test Method | LANXESS GERMANY/T7331 |
|---|---|---|---|
| dielectric strength | 23°C,1.00mm | IEC 60243-1 | 27 KV/mm |
| relative permittivity | 23°C,1MHz | IEC 60250 | 3.80 |
| 23°C,100Hz | IEC 60250 | 4.00 | |
| Compared to the Leakage Tracking Index (CTI) | 解决方案A | IEC 60112 | PLC 2 |
| Mechanical properties | Test Condition | Test Method | LANXESS GERMANY/T7331 |
|---|---|---|---|
| Flexural modulus | 23°C | ISO 178/A | 10300 Mpa |
| Tensile strain | 断裂,23°C | ISO 527-2/5 | 2.8 % |
| tensile strength | 断裂,23°C | ISO 527-2/5 | 145 Mpa |
| Bending Strain | 23°C | 3.0 % | |
| bending strength | 23°C | ASTM D790 | 207 Mpa |
| Tensile creep modulus | 1000hr | ISO 899-1 | 8500 Mpa |
| Tensile modulus | 23°C | ASTM D638 | 9980 Mpa |
| 23°C | ISO 527-2/1 | 10400 Mpa | |
| tensile strength | 断裂,23°C | ASTM D638 | 123 Mpa |
| Tensile creep modulus | 1hr | ISO 899-1 | 10000 Mpa |
| bending strength | 23°C | ISO 178 | 230 Mpa |
| Flexural modulus | 23°C | ASTM D790 | 8550 Mpa |
| elongation | 断裂,23°C | ASTM D638 | 2.5 % |
| flammability | Test Condition | Test Method | LANXESS GERMANY/T7331 |
|---|---|---|---|
| UL flame retardant rating | 0.8mm | UL 94 | HB |
| Burning wire flammability index | 2.0mm | IEC 60695-2-12 | 750 °C |
| Limiting Oxygen Index | ISO 4589-2 | 21 % | |
| UL flame retardant rating | 1.6mm | UL 94 | HB |
| physical property | Test Condition | Test Method | LANXESS GERMANY/T7331 |
|---|---|---|---|
| Shrinkage rate | TD:120°C,2hr,2.00mm3 | ISO 294-4 | 0.20 % |
| MD:270°C,2.00mm2 | ISO 294-4 | 0.30 % | |
| Apparent density | ISO 60 | 0.80 g/cm³ | |
| Water absorption rate | 平衡,23°C,50%RH | ISO 62 | 0.10 % |
| 饱和,23°C | ISO 62 | 0.30 % | |
| Shrinkage rate | TD:270°C,2.00mm2 | ISO 294-4 | 0.90 % |
| Viscosity value | 降低的粘度 | ISO 1628 | 91.0 ml/g |
| Melt volume flow rate | 260°C/5.0kg | ISO 1133 | 30.0 cm3/10min |
| Shrinkage rate | MD:120°C,2hr,2.00mm3 | ISO 294-4 | 0.10 % |
| Thermal performance | Test Condition | Test Method | LANXESS GERMANY/T7331 |
|---|---|---|---|
| Half Interval | --10 | IEC 60216 | 10.2 °C |
| Linear coefficient of thermal expansion | MD：23到55°C | ISO 11359-2 | 3E-05 cm/cm/°C |
| TemperatureIndex | 抗张强度 | IEC 60216 | 155 |
| thermal conductivity | 23°C | ISO 8302 | 0.27 W/m/K |
| Linear coefficient of thermal expansion | TD：23to55°C | ISO 11359-2 | 6E-05 cm/cm/°C |
| TemperatureIndex | 介电强度 | IEC 60216 | 155 |
| RTI Str | UL 746 | 140 °C | |
| melting temperature | ISO 11357-3 | 225to250 °C | |
| vicat | ISO 306/B120 | 205 °C | |
| Heat distortion temperature | 0.45MPa,未退火，HDT | ISO 75-2/B | 220 °C |
| ball-indentation hardness | 220°C | IEC 60695-10-2 | Pass |
| Heat distortion temperature | 1.8MPa,未退火，HDT | ISO 75-2/A | 200 °C |
| RTI Imp | UL 746 | 125 °C | |
| Half Interval | --8 | IEC 60216 | 13.5 °C |
| --9 | IEC 60216 | 10.2 °C | |
| TemperatureIndex | 拉伸冲击强度 | IEC 60216 | 140 |
| RTI Elec | UL 746 | 140 °C |
Contact Us
Get App
Top