plas

Log In | Sign Up

Categories

Plastic Raw Materials

Modified Plastics

Plastic Additives

Color Masterbatch

Plastic Datasheets

Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PC 123R-111 SABIC EU

LEXAN™

Electronic and electrical components,Automotive Applications

Low viscosity,High temperature resistan

--

--

--

--

--

--

--

--

--

--

--

--

--

--

--

Plastic Datasheets

hardness	Test Condition	Test Method	SABIC EU/123R-111
Ball Pressure Test	H 358/30	ISO 2039-1	95.0 Mpa

thermal performance	Test Condition	Test Method	SABIC EU/123R-111
Ball Pressure Test	140°C8	IEC 60695-10-2	通过
Ball Pressure Test		123 to 127°C	IEC 60695-10-2	通过
Hot deformation temperature	0.45 MPa, Unannealed, 4.00 mm, 100 mm Span	ISO 75-2/Be	133 °C
Hot deformation temperature		1.8 MPa, Unannealed, 4.00 mm, 100 mm Span	ISO 75-2/Ae	122 °C
Linear coefficient of thermal expansion	23 to 80°C，Flow	ISO 11359-2	7.0E-5 cm/cm/°C
RTI		UL 746	130 °C
RTI Elec		UL 746	130 °C
RTI Imp		UL 746	130 °C
thermal conductivity		ISO 8302	0.20 W/m/K
Vicat softening temperature	--	ISO 306/B120	141 °C
Vicat softening temperature		--	ISO 306/B50	140 °C

mechanical properties	Test Condition	Test Method	SABIC EU/123R-111
Bending modulus		ISO 178	2300 Mpa
bending strength		ISO 178	90.0 Mpa
Taber abraser	1000 Cycles, 1000 g, CS-17 Wheel	Internal Method	10.0 mg
Tensile modulus		ISO 527-2/1	2350 Mpa
Tensile strain	Break	ISO 527-2/50	100 %
Tensile strain		Yield	ISO 527-2/50	6.0 %
tensile strength	Yield	ISO 527-2/50	63.0 Mpa
tensile strength		Break	ISO 527-2/50	65.0 Mpa

Electrical performance	Test Condition	Test Method	SABIC EU/123R-111
Dielectric strength	3.20 mm, in Oil	IEC 60243-1	17 KV/mm
Dissipation factor	50 Hz	IEC 60250	1.0E-3
		60 Hz	IEC 60250	1.0E-3
		1 MHz	IEC 60250	0.010
Relative permittivity	50 Hz	IEC 60250	2.70
		1 MHz	IEC 60250	2.70
		60 Hz	IEC 60250	2.70
Surface resistivity		IEC 60093	> 1.0E+15 ohms
Volume resistivity		IEC 60093	> 1.0E+15 ohms·cm

Physical properties	Test Condition	Test Method	SABIC EU/123R-111
Melt Volume Flow Rate (MVR)	300°C/1.2 kg	ISO 1133	21.0 cm3/10min
Outdoor applicability		UL 746C	f1
Shrinkage rate	Flow	Internal Method	0.50 - 0.70 %
Water absorption rate	Saturation, 23°C	ISO 62	0.35 %
Water absorption rate		Equilibrium, 23°C, 50% RH	ISO 62	0.15 %

impact performance	Test Condition	Test Method	SABIC EU/123R-111
Impact strength of cantilever beam gap	-30°C	ISO 180/1A	11 kJ/m²
Impact strength of cantilever beam gap		23°C	ISO 180/1A	65 kJ/m²
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Impact strength of simply supported beam without notch		23°C	ISO 179/1eU	无断裂
Suspended wall beam without notch impact strength	-30°C	ISO 180/1U	无断裂
Suspended wall beam without notch impact strength		23°C	ISO 180/1U	无断裂

flammability	Test Condition	Test Method	SABIC EU/123R-111
Burning wire flammability index	1.0 mm	IEC 60695-2-12	850 °C
Extreme Oxygen Index		ISO 4589-2	25 %
UL flame retardant rating	3.0 mm	UL 94	HB
UL flame retardant rating		0.75 mm	UL 94	HB

optical performance	Test Condition	Test Method	SABIC EU/123R-111
Refractive index		ISO 489	1.586
transmissivity	2540 μm	ASTM D1003	88.0 to 90.0 %
turbidity	2540 μm	ASTM D1003	< 0.80 %

injection	Test Condition	Test Method	SABIC EU/123R-111
drying temperature			120 °C
drying time			2.0 to 4.0 hr
Hopper temperature			60 to 80 °C
Mold temperature			80 to 100 °C
Processing (melt) temperature			280 to 300 °C
Spray nozzle temperature			270 to 290 °C
Suggested maximum moisture content			0.020 %
Temperature at the front of the material cylinder			280 to 300 °C
Temperature at the rear of the barrel			260 to 280 °C
Temperature in the middle of the barrel			270 to 290 °C

Contact Us

Get App

Top