Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PA612 SC315 NC010 DUPONT USA
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| Impact strength of simply supported beam without notch | -30°C | ISO 179/1eU | 无断裂 |
| 23°C | ISO 179/1eU | 无断裂 |
| hardness | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| Rockwell hardness | R 计秤 | ISO 2039-2 | 114 |
| Mechanical properties | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| Tensile modulus | ISO 527-2 | 2400 Mpa | |
| Nominal tensile fracture strain | ISO 527-2 | 17 % | |
| Flexural modulus | ISO 178 | 2100 Mpa | |
| Tensile strain | 屈服 | ISO 527-2 | 4.5 % |
| tensile strength | 屈服 | ISO 527-2 | 62.0 Mpa |
| Electrical performance | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| Dissipation Factor | 100 Hz | IEC 62631-2-1 | 0.014 |
| 1 MHz | IEC 62631-2-1 | 0.016 | |
| dielectric strength | IEC 60243-1 | 30 KV/mm | |
| Volume resistivity | IEC 62631-3-1 | 1.0E+13 ohms·m | |
| relative permittivity | 1 MHz | IEC 62631-2-1 | 3.20 |
| 100 Hz | IEC 62631-2-1 | 3.60 | |
| Compared to the Leakage Tracking Index (CTI) | IEC 60112 | V |
| flammability | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| Limiting Oxygen Index | ISO 4589-2 | 27 % |
| Filling analysis | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| Thermal Conductivity of Melt | 0.18 W/m/K | ||
| Melt density | 0.900 g/cm³ | ||
| Emission of Organic Compounds | VDA 277 | 3.10 µgC/g | |
| Specific Heat Capacity of Melt | 2750 J/kg/°C |
| squeeze out | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| drying temperature | 80 °C | ||
| Melt Temperature | 235 to 250 °C | ||
| drying time | 3.0 to 4.0 hr | ||
| Suggested maximum moisture content | 0.060 % | ||
| Extrusion Melt Temperature, Optimum | 240 °C |
| physical property | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| Water absorption rate | 饱和, 23°C, 2.00 mm | ISO 62 | 3.0 % |
| 平衡, 23°C, 2.00 mm, 50% RH | ISO 62 | 1.3 % | |
| viscosity number | 96% H2SO4 | ISO 307 | 95.0 cm³/g |
| Shrinkage rate | 流量 | ISO 294-4 | 1.3 % |
| 横向流量 | ISO 294-4 | 1.4 % |
| Thermal performance | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| melting temperature | ISO 11357-3 | 218 °C | |
| Linear coefficient of thermal expansion | 横向 : -40 到 23°C | ISO 11359-2 | 9.0E-5 cm/cm/°C |
| Heat distortion temperature | 0.45 MPa, 未退火，HDT | ISO 75-2/B | 135 °C |
| Linear coefficient of thermal expansion | 流动 : -40 到 23°C | ISO 11359-2 | 9.0E-5 cm/cm/°C |
| 流动 : 55 到 160°C | ISO 11359-2 | 1.6E-4 cm/cm/°C | |
| vicat | ISO 306/B50 | 181 °C | |
| Heat distortion temperature | 1.8 MPa, 未退火，HDT | ISO 75-2/A | 62.0 °C |
| Linear coefficient of thermal expansion | 横向 : 55 到 160°C | ISO 11359-2 | 1.8E-4 cm/cm/°C |
| 流动 | ISO 11359-2 | 1.1E-4 cm/cm/°C | |
| 横向 | ISO 11359-2 | 1.2E-4 cm/cm/°C |
| injection | Test Condition | Test Method | DUPONT USA/SC315 NC010 |
|---|---|---|---|
| pressure holding | 50.0 to 100 Mpa | ||
| Drying Recommended | yes | ||
| Suggested maximum moisture content | 0.15 % | ||
| Drying time - hot air dryer | 2.0 to 4.0 hr | ||
| Processing (melt) temperature | 230 to 290 °C | ||
| Temperature | 50 to 90 °C | ||
| Melt Temperature, Optimum | 250 °C | ||
| Hold Pressure Time | 4.00 s/mm | ||
| Mold Temperature, Optimum | 70 °C |
Contact Us
Get App
Top