Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

POM 5010 ASAHI JAPAN

TENAC™

Engine parts,Cam,Electronic field,Electrical field,Shell,currency,Engineering accessories

Medium viscosity

Plastic Datasheets

hardness	Test Condition	Test Method	ASAHI JAPAN/5010
Rockwell hardness	M-Scale	ASTM D785	94
Rockwell hardness		R-Scale	ASTM D785	120

thermal performance	Test Condition	Test Method	ASAHI JAPAN/5010
Combustibility (rate)		UL 94	HB
Hot deformation temperature	1.8MPa,Unannealed	ASTM D648	136 °C
		0.45MPa,Unannealed	ISO 75-2/B	165 °C
		1.8MPa,Unannealed	ISO 75-2/A	105 °C
		0.45MPa	ASTM D648	172 °C
		0.45MPa,Unannealed	ASTM D648	172 °C
		HDT	ASTM D648/ISO 75	136(1.8Mpa) ℃（℉）
		1.82MPa	ASTM D648	136 °C
Linear coefficient of thermal expansion	MD	ASTMD696	1E-04 cm/cm/°C
Linear coefficient of thermal expansion				10
melt mass-flow rate		ASTM D1238	22 g/10min
specific heat			1470 J/kg/°C
thermal conductivity			0.23 W/m/K
UL flame retardant rating		UL 94	HB

mechanical properties	Test Condition	Test Method	ASAHI JAPAN/5010
Bending modulus	--	ISO 178	3100 Mpa
			ASTM D790	3040 Mpa
		--	ASTM D790	3040 Mpa
			ASTM D790/ISO 178	3040 kg/cm²(MPa)[Lb/in²]
bending strength		ASTM D790/ISO 178	103 kg/cm²(MPa)[Lb/in²]
bending strength			ASTM D790	107 Mpa
elongation	Break	ASTMD638	30 %
elongation			ASTM D638/ISO 527	45 %
Elongation at Break		ASTM D638	45 %
Impact strength of cantilever beam gap		ASTM D256	69 J/m
Impact strength of cantilever beam gap			ASTM D256/ISO 179	69 kg·cm/cm(J/M)ft·lb/in
Rockwell hardness		ASTM D785	120 R
Rockwell hardness			ASTM D785	94
Taber abraser		ASTM D1044	13.0 mg
Tensile modulus		ISO 527-2	3300 Mpa
tensile strength		ASTM D638/ISO 527	69 kg/cm²(MPa)[Lb/in²]
		--	ASTM D638	72.0 Mpa
			ASTM D638	69 Mpa
		Yield	ISO 527-2	72.0 Mpa
Wear resistance		ASTM D1044	13

Electrical performance	Test Condition	Test Method	ASAHI JAPAN/5010
Arc resistance		ASTM D495	250 sec
Dielectric constant	23°C,1MHz	ASTM D150	3.80
Dielectric strength		ASTM D149	18 KV/mm
Dissipation factor	23°C,1MHz	ASTM D150	7E-03
Surface resistivity		ASTM D257	1.0E+16-1.0E+17 ohms
Volume resistivity	23°C	ASTM D257	1.0E+15-1.0E+16 ohms·cm

other	Test Condition	Test Method	ASAHI JAPAN/5010
characteristic			中粘度

Physical properties	Test Condition	Test Method	ASAHI JAPAN/5010
density		ASTM D792/ISO 1183	1.42
melt mass-flow rate		ASTM D1238/ISO 1133	22 g/10min
melt mass-flow rate		190°C/2.16kg	ISO 1133	22 g/10min
Shrinkage rate	MD	Internal Method	1.8-2.2 %
		Flow		1.8-2.2 %
		Across Flow		1.8-2.2 %
Water absorption rate		ASTM D570	0.2 %
		23°C,24hr,50%RH	ASTM D570	0.20 %
			ASTM D570/ISO 62	0.2 %

flammability	Test Condition	Test Method	ASAHI JAPAN/5010
UL flame retardant rating	1.5mm	UL 94	HB

Get App

Top