Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PA66 1500 ASAHI JAPAN

Leona™

Fasteners,PA board

high molecular weight

Plastic Datasheets

hardness	Test Condition	Test Method	ASAHI JAPAN/1500
Rockwell hardness	M-Sale	ASTM D785	80
		M-Sale	ISO 2039-2	80
		R-Sale	ISO 2039-2	120
		R-Sale	ASTM D785	120

Basic Performance	Test Condition	Test Method	ASAHI JAPAN/1500
Water absorption rate	湿		2.5 %

thermal performance	Test Condition	Test Method	ASAHI JAPAN/1500
Hot deformation temperature	1.8MPa,Unannealed	ASTM D648	70.0 °C
		0.45MPa,Unannealed	ISO 75-2/B	195 °C
		1.82MPa,干	ASTM D-648	70 °C
		1.8MPa,Unannealed	ISO 75-2/A	65.0 °C
		0.45MPa,Unannealed	ASTM D648	230 °C
		0.46MPa,干	ASTM D-648	230 °C
		HDT	ASTM D648/ISO 75	230 ℃（℉）
Linear coefficient of thermal expansion	MD	ASTM D696	8E-05 cm/cm/°C
			ASTM D696/ISO 11359	8 mm/mm.℃
		干	ASTM D-696	8
specific heat	干		1670 J/(kg.k)
specific heat				1670 J/kg/°C
thermal conductivity			0.20 W/m/K
thermal conductivity		干		0.2 W/(m.K)

mechanical properties	Test Condition	Test Method	ASAHI JAPAN/1500
Bending modulus		ASTM D790	2800 Mpa
		23°C	ISO 178	2700 Mpa
			ASTM D790/ISO 178	2790 kg·cm/cm(J/M)ft·lb/in
bending strength	干(湿)	ASTM D-790	118(54) Mpa
			ASTM D790/ISO 178	118 kg·cm/cm(J/M)ft·lb/in
		23°C	ISO 178	110 Mpa
			ASTM D790	118 Mpa
Charpy Notched Impact Strength		ASTM D256/ISO 179	49 kg·cm/cm(J/M)ft·lb/in
elongation	Break	ASTM D638	80 %
Elongation at Break	干(湿)	ASTM D-638	80(270) %
flexural coefficient	干(湿)	ASTM D-790	2.8(1.2) GPa
Impact strength of cantilever beam gap	干(湿)	ASTM D-256	49(176) J/m
Rockwell hardness		ASTM D785	R120
		干(湿)	ASTM D-785	80(55) M Scale
		干(湿)	ASTM D-785	120(105) R scale
Taber abraser	1000Cycles	ASTM D1044	-- mg
Tensile modulus	23°C	ISO 527-2	2900 Mpa
Tensile strain	Yield,23°C	ISO 527-2	4.5 %
Tensile strain		Break,23°C	ISO 527-2	-- %
tensile strength	干(湿)	ASTM D-638	79(57) Mpa
			ASTM D638	79.0 Mpa
		Yield,23°C	ISO 527-2	84.0 Mpa

Electrical performance	Test Condition	Test Method	ASAHI JAPAN/1500
Compared to the anti leakage trace index	3.00mm	IEC 60112	PLC 0
Dielectric strength		IEC 60243-1	20 KV/mm
Dielectric strength			ASTM D149	20 KV/mm
Surface resistivity		ASTM D257	1E+14 ohms
Surface resistivity			IEC 60093	1E+14 ohms
Volume resistivity		ASTM D257	1E+15 ohms·cm
Volume resistivity		23°C	IEC 60093	1E+15 ohms·cm

other	Test Condition	Test Method	ASAHI JAPAN/1500
characteristic			高粘度

Physical properties	Test Condition	Test Method	ASAHI JAPAN/1500
density		ASTM D792/ISO 1183	1.14
Shrinkage rate	MD	Internal Method	1.3-2.0 %
Shrinkage rate		干	旭化成方法	1.3-2.0 %
Water absorption rate	Equilibrium,23°C,50%RH	ISO 62	-- %
		Saturation,23°C		-- %
			ASTM D570/ISO 62	2.5 %
Wear factor	湿	ASTM D-1044	5

impact performance	Test Condition	Test Method	ASAHI JAPAN/1500
Impact strength of simply supported beam without notch		ISO 179	NoBreak

Get App

Top