Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates

POM KFL-4416 SABIC INNOVATIVE US
LNP™ LUBRICOMP™
Casters、household electrical appl
High temperature resistan、UV resistance
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
Impact resistance | Test Condition | Test Method | SABIC INNOVATIVE US/KFL-4416 |
---|---|---|---|
Suspended wall beam without notch impact strength | 23°C | ASTM D4812 | 210 J/m |
Dart impact | 23°C, Energy at Peak | ASTM D3763 | 9.00 J |
Suspended wall beam without notch impact strength | 23°C3 | ISO 180/1U | 17 kJ/m² |
Dart impact | -- | ISO 6603-2 | 2.00 J |
Mechanical properties | Test Condition | Test Method | SABIC INNOVATIVE US/KFL-4416 |
---|---|---|---|
Tensile modulus | --1 | ASTM D638 | 6130 Mpa |
elongation | 屈服 | ASTM D638 | 3.6 % |
bending strength | ASTM D790 | 92.0 Mpa | |
tensile strength | 断裂 | ASTM D638 | 56.0 Mpa |
断裂 | ISO 527-2 | 46.0 Mpa | |
Flexural modulus | -- | ISO 178 | 6300 Mpa |
coefficient of friction | Dynamic | ASTM D3702 | 0.50 |
elongation | 屈服 | ISO 527-2 | 2.3 % |
断裂 | ASTM D638 | 2.6 % | |
tensile strength | 屈服 | ASTM D638 | 56.0 Mpa |
屈服 | ISO 527-2 | 49.0 Mpa | |
coefficient of friction | Static | ASTM D3702 | 0.43 |
Tensile modulus | -- | ISO 527-2/1 | 5800 Mpa |
Flexural modulus | -- | ASTM D790 | 5300 Mpa |
elongation | 断裂 | ISO 527-2 | 4.0 % |
Wear factor | ASTM D3702 | 1.9E+8 10^-8 mm³/N·m |
physical property | Test Condition | Test Method | SABIC INNOVATIVE US/KFL-4416 |
---|---|---|---|
Shrinkage rate | 流动 : 24小时 | ASTM D955 | 1.4 % |
Water absorption rate | 平衡, 23°C, 50% RH | ISO 62 | 0.29 % |
Shrinkage rate | 流量 : 24小时 | ISO 294-4 | 1.5 % |
Water absorption rate | 24 hr, 50% RH | ASTM D570 | 0.16 % |
Shrinkage rate | 横向流量 : 24小时 | ISO 294-4 | 1.3 % |
横向流动 : 24小时 | ASTM D955 | 1.6 % |
Thermal performance | Test Condition | Test Method | SABIC INNOVATIVE US/KFL-4416 |
---|---|---|---|
Heat distortion temperature | 0.45 MPa, 未退火, 3.20 mm,HDT | ASTM D648 | 161 °C |
1.8 MPa, 未退火, 4.00 mm, 64.0 mm 跨距3,HDT | ISO 75-2/Af | 147 °C | |
1.8 MPa, 未退火, 3.20 mm,HDT | ASTM D648 | 132 °C |
injection | Test Condition | Test Method | SABIC INNOVATIVE US/KFL-4416 |
---|---|---|---|
drying time | 4.0 hr | ||
screw speed | 30 to 60 rpm | ||
Temperature in the middle of the barrel | 195 to 205 °C | ||
Temperature at the rear of the barrel | 175 to 190 °C | ||
Processing (melt) temperature | 200 to 215 °C | ||
drying temperature | 80 °C | ||
Temperature at the front of the material cylinder | 210 to 220 °C | ||
Back pressure | 0.200 to 0.300 Mpa | ||
Temperature | 80 to 110 °C |
Contact Us
Get App
Top