plas

Log In | Sign Up

Categories

Plastic Raw Materials

Modified Plastics

Plastic Additives

Color Masterbatch

Plastic Datasheets

Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PA12 5533 SP 01 ARKEMA FRANCE

Pebax®

Medical Supplies

High temperature resistan,Low temperature resistanc

--

--

--

--

--

--

--

--

--

--

--

--

--

--

--

Plastic Datasheets

hardness	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
Shore hardness	Shore D, 15 Sec	ISO 7619-1	50

thermal performance	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
Hot deformation temperature	0.45 MPa, Unannealed	ISO 75-2/B	66.0 °C
Linear coefficient of thermal expansion	Flow	ISO 11359-2	1.7E-4 cm/cm/°C
Melting temperature		ISO 11357-3	159 °C
Vicat softening temperature		ISO 306/B50	142 °C

mechanical properties	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
Nominal tensile fracture strain		ISO 527-2	> 50 %
Tensile modulus		ISO 527-2	170 Mpa
Tensile strain	Yield	ISO 527-2	25 %
Tensile strain		Break	ISO 527-2	> 300 %
tensile strength	100% Strain	ISO 527-2	14.0 Mpa
		Yield	ISO 527-2	12.0 Mpa
		Break	ISO 527-2	52.0 Mpa
		10% Strain	ISO 527-2	10.0 Mpa
Wear resistance		ISO 4649	47.0 mm³

Electrical performance	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
Compared to the anti leakage trace index		IEC 60112	V
Dielectric strength		IEC 60243-1	39 KV/mm
Dissipation factor	100 Hz	IEC 60250	0.11
Dissipation factor		1 MHz	IEC 60250	0.10
Relative permittivity	100 Hz	IEC 60250	9.00
Relative permittivity		1 MHz	IEC 60250	5.00
Surface resistivity		IEC 60093	-- ohms
Volume resistivity		IEC 60093	3.2E+13 ohms·cm

Physical properties	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
Shrinkage rate	横向Flow	ISO 294-4	1.4 %
Shrinkage rate		Flow	ISO 294-4	1.2 %
Water absorption rate	Saturation, 23°C	ISO 62	1.2 %
Water absorption rate		Equilibrium, 23°C, 50% RH	ISO 62	0.60 %

impact performance	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Impact strength of simply supported beam without notch		23°C	ISO 179/1eU	无断裂

flammability	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
Flammability level		UL 94	HB

Filling analysis	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
Melt density			0.830 g/cm³
Specific Heat Capacity of Melt			2800 J/kg/°C
Thermal conductivity of melt			0.18 W/m/K

squeeze out	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
drying temperature			65 to 75 °C
drying time			4.0 to 6.0 hr
Melt Temperature			210 to 230 °C

elastomer	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
Permanent compression deformation	23°C	ISO 815	43 %
tear strength		ISO 34-1	110 kN/m

injection	Test Condition	Test Method	ARKEMA FRANCE/5533 SP 01
drying temperature			65 to 75 °C
drying time			4.0 to 6.0 hr
Mold temperature			25 to 60 °C
Processing (melt) temperature			200 to 270 °C

Contact Us

Get App

Top