PBT 420SEO-7001 PBT vs. - Plastic Material Properties Comparison Chart at Plas.com

Material Selector

All

Plastic Materials Additives Masterbatch Material Selector Price Index Trade Data Plastic News About Us

Material Comparison

Add Comparison Model

Select Products for Comparison (1/4)

Highlight Differences

Hide Same

Product Name / Manufacturer / Model

Grade

Certificates

Reference Price

PBT SABIC INNOVATIVE JAPAN 420SEO-7001

Injection grade

US$ 3,530 / MT

FOB Guangzhou port, China

injection	Test Condition	Test Method	SABIC INNOVATIVE JAPAN/420SEO-7001
Back pressure			0.300 to 0.700 Mpa
Temperature at the front of the material cylinder			255 to 275 °C
Mold temperature			65 to 90 °C
Screw speed			50 to 80 rpm
Processing (melt) temperature			255 to 275 °C
Suggested injection volume			40 to 80 %
Suggested maximum moisture content			0.020 %
Spray nozzle temperature			250 to 270 °C
Exhaust hole depth			0.025 to 0.038 mm
drying temperature			120 °C
Temperature in the middle of the barrel			250 to 270 °C
drying time			3.0 to 4.0 hr
Temperature at the rear of the barrel			245 to 265 °C
Electrical performance	Test Condition	Test Method	SABIC INNOVATIVE JAPAN/420SEO-7001
Dielectric strength	1.60 mm, in Oil	ASTM D149	24 KV/mm
Dielectric strength		0.800 mm, in Oil	IEC 60243-1	23 KV/mm
Compared to the anti leakage trace index		UL 746	PLC 3
Compared to the anti leakage trace index		Solution B	IEC 60112	PLC 4
Dissipation factor	1 MHz	ASTM D150	0.020
Dielectric strength	3.20 mm, in Oil	IEC 60243-1	16 KV/mm
High voltage arc tracing rate		UL 746	PLC 4
Dielectric constant	60 Hz	IEC 60250	3.30
Surface resistivity		IEC 60093	> 1.0E+15 ohms
Dielectric constant	50 Hz	IEC 60250	3.30
Dielectric constant		1 MHz	ASTM D150	3.70
Dielectric strength	1.60 mm, in Oil	IEC 60243-1	22 KV/mm
Dielectric strength		3.20 mm, in Air	ASTM D149	19 KV/mm
Dissipation factor	100 Hz	ASTM D150	2.0E-3
Dissipation factor		50 Hz	IEC 60250	1.0E-3
High arc combustion index		UL 746	PLC 0
Hot wire ignition		UL 746	PLC 2
Dissipation factor	60 Hz	IEC 60250	1.0E-3
Dielectric constant	100 Hz	ASTM D150	3.80
Volume resistivity		ASTM D257	> 1.0E+15 ohms·cm
Dissipation factor	1 MHz	IEC 60250	0.010
Arc resistance		ASTM D495	PLC 6
Dielectric constant	1 MHz	IEC 60250	3.30
Compared to the anti leakage trace index	--	IEC 60112	PLC 3
Physical properties	Test Condition	Test Method	SABIC INNOVATIVE JAPAN/420SEO-7001
Shrinkage rate	Across FlowFlow 2	Internal Method	0.40 - 0.80 %
Shrinkage rate		Across FlowFlow : 3.20 mm	Internal Method	0.50 - 1.0 %
Water absorption rate	Saturation, 23°C	ISO 62	0.090 %
Shrinkage rate	Flow : 3.20 mm	Internal Method	0.50 - 0.70 %
melt mass-flow rate	250°C/5.0 kg	ASTM D1238	42 g/10 min
Water absorption rate	Equilibrium, 23°C, 50% RH	ISO 62	0.070 %
Specific volume		ASTM D792	0.610 cm³/g
Shrinkage rate	Flow 2	Internal Method	0.10 - 0.50 %
Outdoor applicability		UL 746C	f2
Melt Volume Flow Rate (MVR)	250°C/5.0 kg	ISO 1133	29.0 cm3/10min
flammability	Test Condition	Test Method	SABIC INNOVATIVE JAPAN/420SEO-7001
UL flame retardant rating	0.40 mm	UL 94	V-2
Extreme Oxygen Index		ISO 4589-2	32 %
Burning wire flammability index	1.0 mm	IEC 60695-2-12	960 °C
UL flame retardant rating	0.71 mm	UL 94	V-0
UL flame retardant rating		2.0 mm	UL 94	5VA
mechanical properties	Test Condition	Test Method	SABIC INNOVATIVE JAPAN/420SEO-7001
elongation	Break	ISO 527-2/5	1.9 %
Bending modulus	50.0 mm Span5	ASTM D790	9800 Mpa
tensile strength	Yield	ISO 527-2/5	120 Mpa
elongation	Yield4	ASTM D638	2.0 %
Taber abraser	1000 Cycles, 1000 g, CS-17 Wheel	Internal Method	22.0 mg
bending strength	Break, 50.0 mm Span5	ASTM D790	186 Mpa
elongation	Break4	ASTM D638	2.0 %
tensile strength	Break	ISO 527-2/5	120 Mpa
tensile strength		Yield4	ASTM D638	120 Mpa
Tensile modulus	--3	ASTM D638	12000 Mpa
elongation	Yield	ISO 527-2/5	1.9 %
bending strength	--	ISO 178	180 Mpa
Tensile modulus	--	ISO 527-2/1	10000 Mpa
Bending modulus	--6	ISO 178	9500 Mpa
tensile strength	Break4	ASTM D638	120 Mpa
thermal performance	Test Condition	Test Method	SABIC INNOVATIVE JAPAN/420SEO-7001
Linear coefficient of thermal expansion	Across Flow : -40 to 40°C	ASTM E831	8.9E-5 cm/cm/°C
Linear coefficient of thermal expansion		Across Flow : -40°C	ISO 11359-2	8.9E-5 cm/cm/°C
Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 100 mm Span9	ISO 75-2/Ae	195 °C
		1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span8	ISO 75-2/Af	200 °C
		0.45 MPa, Unannealed, 3.20 mm	ASTM D648	212 °C
Linear coefficient of thermal expansion	Flow : -40 to 40°C	ASTM E831	2.5E-5 cm/cm/°C
Hot deformation temperature	0.45 MPa, Unannealed, 4.00 mm, 100 mm Span9	ISO 75-2/Be	220 °C
Linear coefficient of thermal expansion	Flow : 23 to 80°C	ISO 11359-2	2.5E-5 cm/cm/°C
RTI Elec		UL 746	130 °C
RTI Imp		UL 746	130 °C
Vicat softening temperature	--	ISO 306/A50	220 °C
Linear coefficient of thermal expansion	Across Flow : 23 to 80°C	ISO 11359-2	1.2E-4 cm/cm/°C
RTI		UL 746	140 °C
thermal conductivity		ISO 8302	0.25 W/m/K
Hot deformation temperature	1.8 MPa, Unannealed, 3.20 mm	ASTM D648	200 °C
Ball Pressure Test	123 to 127°C	IEC 60695-10-2	通过
Vicat softening temperature	--	ASTM D152510	200 °C
impact performance	Test Condition	Test Method	SABIC INNOVATIVE JAPAN/420SEO-7001
Suspended wall beam without notch impact strength	-30°C8	ISO 180/1U	45 kJ/m²
		23°C8	ISO 180/1U	45 kJ/m²
		23°C	ASTM D4812	620 J/m
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	50 kJ/m²
Charpy Notched Impact Strength	-30°C	ISO 179/1eA	6.0 kJ/m²
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	50 kJ/m²
Dart impact	23°C, Total Energy	ASTM D3763	5.00 J
Charpy Notched Impact Strength	23°C	ISO 179/1eA	7.0 kJ/m²
hardness	Test Condition	Test Method	SABIC INNOVATIVE JAPAN/420SEO-7001
Rockwell hardness	R-Scale	ASTM D785	119
Rockwell hardness		R -Sale	ISO 2039-2	119
Ball Pressure Test	H 358/30	ISO 2039-1	118 Mpa

Supplier Join

Get App

Top

Sourcing & Prices

Selling & Verification

Explore Materials

Price Index