Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PA6 B3EG5 BASF GERMANY

Ultramid®

Automotive sector

enhance

Plastic Datasheets

Other performance	Test Condition	Test Method	BASF GERMANY/B3EG5
Compared to the Leakage Traceability Index (CTI)	干/湿		干/湿
impact strength	+23℃干/湿		10/30 J

thermal performance	Test Condition	Test Method	BASF GERMANY/B3EG5
Combustibility (rate)		UL 94	HB
Hot deformation temperature	0.45MPa负荷，Dry		220 °C
		HDT	ASTM D648/ISO 75	210(1.80MPa) ℃（℉）
		1.8MPa负荷，Dry		210 °C
		1.8MPa,Unannealed	°C	239to261
Linear coefficient of thermal expansion	23-80℃Dry		2-2.5/6-7
Linear coefficient of thermal expansion			ASTM D696/ISO 11359	0.2-0.25 mm/mm.℃
Maximum operating temperature			200 °C
Melting temperature			220 ℃（℉）
specific heat	Dry		1.5 J/(g.K)
Temperature index	在20000h/5000h，后拉伸强度下降50%时		120/150 °C
thermal conductivity	Dry		0.26 W/(m.K)

mechanical properties	Test Condition	Test Method	BASF GERMANY/B3EG5
Ball Pressure Test	干/湿		210/140 Mpa
Bending modulus	干/湿		7400/4200 Mpa
Bending modulus			ASTM D790/ISO 178	7400 kg/cm²(MPa)[Lb/in²]
bending strength		ASTM D790/ISO 178	2020 kg/cm²(MPa)[Lb/in²]
bending strength		干/湿		220/150 Mpa
Charpy Notched Impact Strength	干/湿		80/105 KJ/m
		30℃，干		75 KJ/m
		+23℃，干/湿		12/25 KJ/m
			ASTM D256/ISO 179	75 kg·cm/cm(J/M)ft·lb/in
		30℃，干/湿		10 KJ/m
elongation	≤0.5%, +23℃，湿		3000 Mpa
Elongation at Break		ASTM D638/ISO 527	3.5 %
Elongation at Break		干/湿，V=50mm/min		3.5/8.5 %
Fracture stress (V=50mm/min)	干/湿		160/105 Mpa
Impact strength of cantilever beam gap		ASTM D256/ISO 179	12 kg·cm/cm(J/M)ft·lb/in
Impact strength of cantilever beam gap		+23℃，干/湿		12/17 KJ/m
Tensile creep modulus	1000h，湿		3000 Mpa
Tensile modulus		ASTM D638/ISO 527	8000 kg/cm²(MPa)[Lb/in²]
		干/湿		8000/5500 Mpa
		23℃		0.01.0.01E0.05-0.01.0.04E0.05 MPa
Tensile strain	Break,23℃	%	2.5-3.0
tensile strength	Break,23℃		95.17to284.83 MPa
Tensile yield stress (V=50mm/min)	干/湿		160/105 Mpa

Electrical performance	Test Condition	Test Method	BASF GERMANY/B3EG5
Dielectric constant		ASTM D150/IEC 60250	3.8
Dielectric constant		1MHz，干/湿		3.8/7
Dielectric strength	K20/P50，干/湿		80/70 KV/mm
Loss angle	1MHz，干/湿		0.025/0.24
Surface resistivity	干/湿		10 Ω
Volume resistivity	干/湿		10 Ω.cm
Volume resistivity			ASTM D257/IEC 60093	1E 13 Ω.cm

other	Test Condition	Test Method	BASF GERMANY/B3EG5
characteristic			高机械强度、刚度和热稳定性.低温抗冲击性

Physical properties	Test Method	BASF GERMANY/B3EG5
density	ASTM D792/ISO 1183	1320
melt mass-flow rate	ASTM D1238/ISO 1133	55 （cm3/10min 275℃/5kg ) g/10min
Shrinkage rate	ASTM D955	0.35 %
Shrinkage rate	23℃	%	0.20-1.0
Water absorption rate	ASTM D570/ISO 62	6.8-7.4 %

impact performance	Test Condition	Test Method	BASF GERMANY/B3EG5
Impact strength of simply supported beam without notch	23℃	kJ/m²	10.679to17.642

Get App

Top