plas

Log In | Sign Up

Categories

Plastic Raw Materials

Modified Plastics

Plastic Additives

Color Masterbatch

Plastic Datasheets

Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PC/PET XL1339U-BK1370 SABIC EU

XENOY™

Automotive components,Electronic and electrical components

High heat resistance

--

--

--

--

--

--

--

--

--

--

--

--

--

--

--

Plastic Datasheets

thermal performance	Test Condition	Test Method	SABIC EU/XL1339U-BK1370
Hot deformation temperature	0.45 MPa, Unannealed, 4.00 mm, 100 mm Span	ISO 75-2/Be	125 °C
Hot deformation temperature		1.8 MPa, Unannealed, 4.00 mm, 100 mm Span	ISO 75-2/Ae	105 °C
Linear coefficient of thermal expansion	Flow : -30 to 30°C	ASTM D696	7.6E-5 cm/cm/°C
Linear coefficient of thermal expansion		Across Flow : -30 to 30°C	ASTM D696	7.9E-5 cm/cm/°C
thermal conductivity		ASTM C177	0.18 W/m/K
Vicat softening temperature	--	ISO 306/B120	135 °C
		--	ISO 306/B50	130 °C
		--	ISO 306/A50	140 °C

mechanical properties	Test Condition	Test Method	SABIC EU/XL1339U-BK1370
Bending modulus	--5	ISO 178	2200 Mpa
Bending modulus		50.0 mm Span4	ASTM D790	2090 Mpa
bending strength	Yield, 50.0 mm Span4	ASTM D790	94.0 Mpa
bending strength		--5,6	ISO 178	80.0 Mpa
elongation	Yield	ISO 527-2/50	5.0 %
		Yield3	ASTM D638	5.0 %
		Break3	ASTM D638	110 %
		Break	ISO 527-2/50	70 %
Poisson's ratio		ASTM E132	0.40
Taber abraser	1000 Cycles, 1000 g, CS-17 Wheel	ASTM D1044	16.0 mg
Tensile modulus		ASTM D638	2090 Mpa
tensile strength	Yield	ISO 527-2/50	55.0 Mpa
		Break	ISO 527-2/50	40.0 Mpa
		Break3	ASTM D638	49.0 Mpa
		Yield3	ASTM D638	49.0 Mpa

Electrical performance	Test Condition	Test Method	SABIC EU/XL1339U-BK1370
Dielectric constant	1 MHz	ASTM D150	3.10
		50 kHz	ASTM D150	3.30
		60 Hz	ASTM D150	3.30
Dielectric strength	3.20 mm, in Oil	ASTM D149	17 KV/mm
Dissipation factor	1 MHz	ASTM D150	0.020
		60 Hz	ASTM D150	2.0E-3
		50 Hz	ASTM D150	2.0E-3
Surface resistivity		ASTM D257	> 1.0E+15 ohms
Volume resistivity		ASTM D257	> 1.0E+14 ohms·cm

Physical properties	Test Condition	Test Method	SABIC EU/XL1339U-BK1370
Melt Volume Flow Rate (MVR)	265°C/1.2 kg	ISO 1133	4.00 cm3/10min
Shrinkage rate	Flow	Internal Method	0.50 - 0.80 %
Shrinkage rate		Across FlowFlow	Internal Method	0.50 - 0.80 %
Water absorption rate	24 hr	ASTM D570	0.10 %
		Equilibrium, 23°C	ASTM D570	0.70 %
		Equilibrium, 50% RH	ASTM D570	0.20 %

impact performance	Test Condition	Test Method	SABIC EU/XL1339U-BK1370
Charpy Notched Impact Strength	23°C	ISO 179/1eA	45 kJ/m²
Charpy Notched Impact Strength		-30°C	ISO 179/1eA	35 kJ/m²
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Impact strength of simply supported beam without notch		23°C	ISO 179/1eU	无断裂
Suspended wall beam without notch impact strength	-30°C	ISO 180/1U	无断裂
Suspended wall beam without notch impact strength		23°C	ISO 180/1U	无断裂

injection	Test Condition	Test Method	SABIC EU/XL1339U-BK1370
Back pressure			0.300 to 0.700 Mpa
drying temperature			110 °C
drying time			4.0 to 6.0 hr
Exhaust hole depth			0.013 to 0.020 mm
Mold temperature			65 to 90 °C
Processing (melt) temperature			260 to 275 °C
Screw speed			50 to 80 rpm
Spray nozzle temperature			255 to 270 °C
Suggested injection volume			50 to 80 %
Suggested maximum moisture content			0.020 %
Temperature at the front of the material cylinder			255 to 275 °C
Temperature at the rear of the barrel			245 to 265 °C
Temperature in the middle of the barrel			250 to 270 °C

Contact Us

Get App

Top