Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PBT 310SE0 SABIC INNOVATIVE US
VALOX™
Spool、Shell、switch、Home appliance components、Electronic field、Electrical field
Flame retardant
UL
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | SABIC INNOVATIVE US/310SE0 |
|---|---|---|---|
| Impact strength of simply supported beam without notch | -30°C | ISO 179/1eU | NoBreak |
| Impact strength of cantilever beam gap | 23°C | ASTM D256 | 37 J/m |
| Dart impact | 23°C,TotalEnergy | ASTM D3763 | 200 J |
| Charpy Notched Impact Strength | 23°C10 | ISO 179/1eA | 8.0 kJ/m² |
| Impact strength of simply supported beam without notch | 23°C | ISO 179/1eU | NoBreak |
| Charpy Notched Impact Strength | 23°C | ISO 179/2C | 4.0 kJ/m² |
| -30°C10 | ISO 179/1eA | 4.0 kJ/m² | |
| Impact strength of cantilever beam gap | -30°C | ASTM D256 | 22 J/m |
| -30°C | ISO 180/1A | 3.0 kJ/m² | |
| 23°C | ASTM D4812 | 1600 J/m | |
| Suspended wall beam without notch impact strength | 23°C | ISO 180/1U | NoBreak |
| Impact strength of cantilever beam gap | 23°C | ISO 180/1A | 5.0 kJ/m² |
| Suspended wall beam without notch impact strength | -30°C | ISO 180/1U | NoBreak |
| hardness | Test Condition | Test Method | SABIC INNOVATIVE US/310SE0 |
|---|---|---|---|
| Rockwell hardness | R级 | ISO 2039-2 | 120 |
| ball-indentation hardness | H358/30 | ISO 2039-1 | 105 Mpa |
| Mechanical properties | Test Condition | Test Method | SABIC INNOVATIVE US/310SE0 |
|---|---|---|---|
| Tensile modulus | ISO 527-2/1 | 2800 Mpa | |
| tensile strength | Yield | ASTM D638 | 58.0 Mpa |
| Flexural modulus | 50.0mmSpan | ASTM D790 | 2620 Mpa |
| Tensile strain | 屈服 | ISO 527-2/50 | 6.0 % |
| tensile strength | 断裂 | ISO 527-2/50 | 40.0 Mpa |
| Tensile modulus | ASTM D638 | 2820 Mpa | |
| tensile strength | 屈服 | ISO 527-2/50 | 55.0 Mpa |
| elongation | 断裂 | ASTM D638 | 20 % |
| tensile strength | Break | ASTM D638 | 58.0 Mpa |
| bending strength | Yield,50.0mmSpan | ASTM D790 | 101 Mpa |
| Tensile strain | Yield | ASTM D638 | 20 % |
| bending strength | ISO 178 | 90.0 Mpa | |
| Flexural modulus | ISO 178 | 2600 Mpa | |
| Taber abraser | 1000Cycles,1000g,CS-17转轮 | 内部方法 | 19.0 mg |
| Tensile strain | 断裂 | ISO 527-2/50 | 20 % |
| Electrical performance | Test Condition | Test Method | SABIC INNOVATIVE US/310SE0 |
|---|---|---|---|
| relative permittivity | 60Hz | IEC 60250 | 2.90 |
| dielectric strength | 0.800mm,在油中 | IEC 60243-1 | 31 KV/mm |
| relative permittivity | 50Hz | IEC 60250 | 2.90 |
| 100Hz | IEC 60250 | 3.10 | |
| Dissipation Factor | 100Hz | IEC 60250 | 2E-03 |
| High arc combustion index (HAI) | HAI | UL 746 | PLC 0 |
| dielectric strength | 3.20mm,在油中 | IEC 60243-1 | 15 KV/mm |
| relative permittivity | 1MHz | IEC 60250 | 2.80 |
| Compared to the Leakage Tracking Index (CTI) | 解决方案B | IEC 60112 | PLC 4 |
| High Voltage Arc Traceability Rate (HVTR) | PLC | UL 746 | |
| Dissipation Factor | 50Hz | IEC 60250 | 1E-03 |
| 60Hz | IEC 60250 | 1E-03 | |
| 1MHz | IEC 60250 | 0.010 | |
| Compared to the Leakage Tracking Index (CTI) | -- | IEC 60112 | PLC 3 |
| High Voltage Arc Traceability Rate (HVTR) | HVTR | UL 746 | PLC 4 |
| Volume resistivity | IEC 60093 | >1.0E+15 ohms·cm | |
| Hot wire ignition (HWI) | HWI | UL 746 | PLC 2 |
| dielectric strength | 1.00mm15 | IEC 60243-1 | 18 KV/mm |
| 1.60mm,在油中 | IEC 60243-1 | 24 KV/mm | |
| arc resistance | ASTM D495 | PLC6 | |
| dielectric strength | 3.20mm,inAir | ASTM D149 | 18 KV/mm |
| 1.60mm,在油中 | ASTM D149 | 22 KV/mm | |
| Surface Resistivity | IEC 60093 | >1.0E+15 ohms | |
| Compared to the Leakage Tracking Index (CTI) | CTI | UL 746 | PLC 3 |
| flammability | Test Condition | Test Method | SABIC INNOVATIVE US/310SE0 |
|---|---|---|---|
| UL flame retardant rating | 3.0mm | UL 94 | 5VA |
| Burning wire flammability index | 1.0mm | IEC 60695-2-12 | 960 °C |
| Limiting Oxygen Index | ISO 4589-2 | 30 % | |
| UL flame retardant rating | 0.71mm | UL 94 | V-0 |
| physical property | Test Condition | Test Method | SABIC INNOVATIVE US/310SE0 |
|---|---|---|---|
| Shrinkage rate | MD：3.20mm | 内部方法 | 1.5-2.3 % |
| Water absorption rate | 平衡,23°C,50%RH | ISO 62 | 0.080 % |
| Shrinkage rate | MD：--2 | 内部方法 | 1.1-1.8 % |
| Water absorption rate | 饱和,23°C | ISO 62 | 0.36 % |
| Shrinkage rate | MD：--3 | 内部方法 | 1.5-2.3 % |
| density | ISO 1183 | 1.40 g/cm³ | |
| Shrinkage rate | MD：--4 | 内部方法 | 0.90-1.6 % |
| Melt volume flow rate | 250°C/2.16kg | ISO 1133 | 8.00 cm3/10min |
| melt mass-flow rate | 250°C/2.16kg | ASTM D1238 | 8.6 g/10min |
| Shrinkage rate | TD：--2 | 内部方法 | 0.90-1.9 % |
| TD：--3 | 内部方法 | 1.6-2.4 % | |
| TD：--4 | 内部方法 | 1.0-1.7 % | |
| density | ASTM D792 | 1.40 g/cm³ | |
| Specific volume | ASTM D792 | 0.710 cm³/g |
| Thermal performance | Test Condition | Test Method | SABIC INNOVATIVE US/310SE0 |
|---|---|---|---|
| Heat distortion temperature | 0.45MPa,Unannealed,100mmSpan，HDT | ISO 75-2/Be | 135 °C |
| 1.8MPa,未退火,6.40mm，HDT | ASTM D648 | 71.0 °C | |
| Linear coefficient of thermal expansion | MD：60to138°C | ASTME831 | 1.3E-04 cm/cm/°C |
| Heat distortion temperature | 0.45MPa,未退火,6.40mm，HDT | ASTM D648 | 162 °C |
| RTI Str | UL 746 | 140 °C | |
| vicat | -- | ISO 306/B120 | 165 °C |
| Linear coefficient of thermal expansion | MD：23to60°C | ISO 11359-2 | 1E-04 cm/cm/°C |
| thermal conductivity | ISO 8302 | 0.24 W/m/K | |
| Heat distortion temperature | 1.8MPa,未退火,100mm跨距12，HDT | ISO 75-2/Ae | 60.0 °C |
| Linear coefficient of thermal expansion | TD：-40到40°C | ASTME831 | 7.9E-05 cm/cm/°C |
| MD：-40to40°C | ISO 11359-2 | 7.6E-05 cm/cm/°C | |
| vicat | ASTM D152514 | 165 °C | |
| -- | ISO 306/A50 | 212 °C | |
| -- | ISO 306/B50 | 165 °C | |
| Linear coefficient of thermal expansion | MD：-40to40°C | ASTME831 | 7.9E-05 cm/cm/°C |
| TD：-40to40°C | ISO 11359-2 | 7.3E-05 cm/cm/°C | |
| RTI Imp | UL 746 | 120 °C | |
| Heat distortion temperature | 1.8MPa,未退火,64.0mm跨距13，HDT | ISO 75-2/Af | 71.0 °C |
| Linear coefficient of thermal expansion | TD：23to60°C | ISO 11359-2 | 1E-04 cm/cm/°C |
| Heat distortion temperature | 1.8MPa,未退火,3.20mm，HDT | ASTM D648 | 74.0 °C |
| ball-indentation hardness | 125°C | IEC 60695-10-2 | Pass |
| RTI Elec | UL 746 | 120 °C |
Contact Us
Get App
Top