plas

Log In | Sign Up

Categories

Plastic Raw Materials

Modified Plastics

Plastic Additives

Color Masterbatch

Plastic Datasheets

Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PEI 1000 GY SABIC INNOVATIVE US

ULTEM™

Automotive sector,Electrical field,Electronic field

Glass fiber reinforced,Flame retardant,enhance

UL

--

--

--

--

--

--

--

--

--

--

--

--

--

--

--

Plastic Datasheets

hardness	Test Condition	Test Method	SABIC INNOVATIVE US/1000 GY
Ball Pressure Test	H 358/30	ISO 2039-1	140 Mpa

thermal performance	Test Condition	Test Method	SABIC INNOVATIVE US/1000 GY
Ball Pressure Test	123 to 127°C	IEC 60695-10-2	通过
Hot deformation temperature	0.45 MPa, Unannealed, 4.00 mm, 100 mm Span	ISO 75-2/Be	200 °C
Hot deformation temperature		1.8 MPa, Unannealed, 4.00 mm, 100 mm Span	ISO 75-2/Ae	190 °C
Linear coefficient of thermal expansion	Across Flow : 23 to 150°C	ISO 11359-2	5.0E-5 cm/cm/°C
Linear coefficient of thermal expansion		Flow : 23 to 150°C	ISO 11359-2	5.0E-5 cm/cm/°C
RTI		UL 746	170 °C
RTI Elec		UL 746	170 °C
RTI Imp		UL 746	170 °C
thermal conductivity		ISO 8302	0.24 W/m/K
Vicat softening temperature	--	ISO 306/B120	212 °C
		--	ISO 306/B50	211 °C
		--	ISO 306/A50	215 °C

mechanical properties	Test Condition	Test Method	SABIC INNOVATIVE US/1000 GY
Bending modulus		ISO 178	3300 Mpa
bending strength		ISO 178	160 Mpa
Taber abraser	1000 Cycles, 1000 g, CS-17 Wheel	Internal Method	10.0 mg
Tensile modulus		ISO 527-2/1	3200 Mpa
Tensile strain	Break	ISO 527-2/50	60 %
Tensile strain		Yield	ISO 527-2/50	6.0 %
tensile strength	Yield	ISO 527-2/50	105 Mpa
tensile strength		Break	ISO 527-2/50	85.0 Mpa

Electrical performance	Test Condition	Test Method	SABIC INNOVATIVE US/1000 GY
Compared to the anti leakage trace index	Solution B	IEC 60112	V
Compared to the anti leakage trace index		--	IEC 60112	V
Dielectric strength	3.20 mm, in Oil	IEC 60243-1	16 KV/mm
		0.800 mm, in Oil	IEC 60243-1	33 KV/mm
		1.60 mm, in Oil	IEC 60243-1	25 KV/mm
Dissipation factor	50 Hz	IEC 60250	5.0E-4
		60 Hz	IEC 60250	5.0E-4
		2.45 GHz	IEC 60250	2.5E-3
		1 MHz	IEC 60250	6.0E-3
Relative permittivity	50 Hz	IEC 60250	2.90
		1 MHz	IEC 60250	2.90
		60 Hz	IEC 60250	2.90
Surface resistivity		IEC 60093	> 1.0E+15 ohms
Volume resistivity		IEC 60093	1.0E+15 ohms·cm

Physical properties	Test Condition	Test Method	SABIC INNOVATIVE US/1000 GY
Melt Volume Flow Rate (MVR)	360°C/5.0 kg	ISO 1133	13.0 cm3/10min
Shrinkage rate	Flow	Internal Method	0.50 - 0.70 %
Water absorption rate	Saturation, 23°C	ISO 62	1.3 %
Water absorption rate		Equilibrium, 23°C, 50% RH	ISO 62	0.70 %

impact performance	Test Condition	Test Method	SABIC INNOVATIVE US/1000 GY
Impact strength of cantilever beam gap	-30°C	ISO 180/1A	6.0 kJ/m²
Impact strength of cantilever beam gap		23°C	ISO 180/1A	6.0 kJ/m²
Suspended wall beam without notch impact strength	-30°C	ISO 180/1U	无断裂
Suspended wall beam without notch impact strength		23°C	ISO 180/1U	无断裂

flammability	Test Condition	Test Method	SABIC INNOVATIVE US/1000 GY
Burning wire flammability index	3.2 mm	IEC 60695-2-12	960 °C
Extreme Oxygen Index		ISO 4589-2	47 %
UL flame retardant rating	3.0 mm	UL 94	5VA
		0.75 mm	UL 94	V-0
		0.40 mm	UL 94	V-2

injection	Test Condition	Test Method	SABIC INNOVATIVE US/1000 GY
drying temperature			150 °C
drying time			4.0 to 6.0 hr
Hopper temperature			80 to 120 °C
Mold temperature			140 to 180 °C
Processing (melt) temperature			370 to 410 °C
Spray nozzle temperature			350 to 405 °C
Suggested maximum moisture content			0.020 %
Temperature at the front of the material cylinder			360 to 415 °C
Temperature at the rear of the barrel			340 to 395 °C
Temperature in the middle of the barrel			350 to 405 °C

Contact Us

Get App

Top