Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PBT 4012G SABIC INNOVATIVE US
VALOX™
Laptop case
Ductility,Fast forming cycle
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | SABIC INNOVATIVE US/4012G |
|---|---|---|---|
| Suspended wall beam without notch impact strength | -30°C | ISO 180/1U | 37 kJ/m² |
| 23°C | ISO 180/1U | 37 kJ/m² | |
| Charpy Notched Impact Strength | 23°C | ISO 179/1eA | 7.0 kJ/m² |
| Dart impact | 23°C,TotalEnergy | ASTM D3763 | 4.00 J |
| Impact strength of cantilever beam gap | -30°C | ASTM D256 | 74 J/m |
| 23°C | ASTM D256 | 74 J/m | |
| Charpy Notched Impact Strength | -30°C | ISO 179/1eA | 6.0 kJ/m² |
| Impact strength of cantilever beam gap | -30°C | ISO 180/1A | 6.0 kJ/m² |
| Impact strength of simply supported beam without notch | 23°C | ISO 179/1eU | 45 kJ/m² |
| Impact strength of cantilever beam gap | 23°C | ISO 180/1A | 6.0 kJ/m² |
| Impact strength of simply supported beam without notch | -30°C | ISO 179/1eU | 45 kJ/m² |
| hardness | Test Condition | Test Method | SABIC INNOVATIVE US/4012G |
|---|---|---|---|
| ball-indentation hardness | H358/30 | ISO 2039-1 | 117 Mpa |
| Electrical performance | Test Condition | Test Method | SABIC INNOVATIVE US/4012G |
|---|---|---|---|
| relative permittivity | 60Hz | IEC 60250 | 3.10 |
| 50Hz | IEC 60250 | 3.10 | |
| dielectric strength | 0.800mm,在油中 | IEC 60243-1 | 30 KV/mm |
| 3.20mm,在油中 | IEC 60243-1 | 17 KV/mm | |
| relative permittivity | 1MHz | IEC 60250 | 3.00 |
| Dissipation Factor | 50Hz | IEC 60250 | 1E-03 |
| 60Hz | IEC 60250 | 1E-03 | |
| 1MHz | IEC 60250 | 0.014 | |
| Compared to the Leakage Tracking Index (CTI) | -- | IEC 60112 | V |
| Volume resistivity | IEC 60093 | >1.0E+15 ohms·cm | |
| Compared to the Leakage Tracking Index (CTI) | 解决方案B | IEC 60112 | V |
| dielectric strength | 1.60mm,在油中 | IEC 60243-1 | 25 KV/mm |
| Surface Resistivity | IEC 60093 | >1.0E+15 ohms |
| Mechanical properties | Test Condition | Test Method | SABIC INNOVATIVE US/4012G |
|---|---|---|---|
| Tensile modulus | ISO 527-2/1 | 4500 Mpa | |
| tensile strength | 断裂 | ISO 527-2/5 | 72.0 Mpa |
| elongation | 屈服 | ASTM D638 | 3.0 % |
| Tensile strain | 屈服 | ISO 527-2/5 | 4.0 % |
| Flexural modulus | 50.0mmSpan | ASTM D790 | 3940 Mpa |
| tensile strength | 屈服 | ISO 527-2/5 | 72.0 Mpa |
| Tensile modulus | ASTM D638 | 4600 Mpa | |
| elongation | 断裂 | ASTM D638 | 3.0 % |
| bending strength | Yield,50.0mmSpan | ASTM D790 | 110 Mpa |
| tensile strength | Break | ASTM D638 | 75.0 Mpa |
| bending strength | ISO 178 | 110 Mpa | |
| Flexural modulus | ISO 178 | 3500 Mpa | |
| Tensile strain | 断裂 | ISO 527-2/5 | 4.0 % |
| tensile strength | 屈服 | ASTM D638 | 75.0 Mpa |
| flammability | Test Condition | Test Method | SABIC INNOVATIVE US/4012G |
|---|---|---|---|
| Burning wire flammability index | 1.0mm | IEC 60695-2-12 | 750 °C |
| UL flame retardant rating | 1.6mm | UL 94 | HB |
| physical property | Test Condition | Test Method | SABIC INNOVATIVE US/4012G |
|---|---|---|---|
| Shrinkage rate | MD：3.20mm | 内部方法 | 0.60-1.6 % |
| melt mass-flow rate | 250°C/1.2kg | ASTM D1238 | 10 g/10min |
| Shrinkage rate | TD2 | 内部方法 | 0.70-1.0 % |
| Water absorption rate | 平衡,23°C,50%RH | ISO 62 | 0.070 % |
| Melt volume flow rate | 250°C/1.2kg | ISO 1133 | 9.00 cm3/10min |
| Shrinkage rate | MD：--2 | 内部方法 | 0.60-0.90 % |
| Water absorption rate | 饱和,23°C | ISO 62 | 0.20 % |
| density | ASTM D792 | 1.39 g/cm³ | |
| ISO 1183 | 1.39 g/cm³ |
| Thermal performance | Test Condition | Test Method | SABIC INNOVATIVE US/4012G |
|---|---|---|---|
| Heat distortion temperature | 0.45MPa,Unannealed,100mmSpan，HDT | ISO 75-2/Be | 215 °C |
| vicat | -- | ISO 306/B120 | 208 °C |
| Linear coefficient of thermal expansion | TD：-40到40°C | ASTME831 | 8E-05 cm/cm/°C |
| TD：23到150°C | ISO 11359-2 | 8.5E-05 cm/cm/°C | |
| vicat | -- | ISO 306/B50 | 205 °C |
| Linear coefficient of thermal expansion | MD：-40到40°C | ASTME831 | 6E-05 cm/cm/°C |
| vicat | ASTM D152511 | 205 °C | |
| Linear coefficient of thermal expansion | MD：23到80°C | ISO 11359-2 | 6E-05 cm/cm/°C |
| Heat distortion temperature | 1.8MPa,Unannealed,100mmSpan，HDT | ISO 75-2/Ae | 170 °C |
| 1.8MPa,未退火,3.20mm，HDT | ASTM D648 | 175 °C | |
| Linear coefficient of thermal expansion | TD：23到80°C | ISO 11359-2 | 8E-05 cm/cm/°C |
| ball-indentation hardness | 125°C | IEC 60695-10-2 | Pass |
Contact Us
Get App
Top