Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PCTG 6002 EASTMAN USA

Tritan™

Electrical applications,Household daily necessities

Chemical resistance,Hydrolysis resistance

Plastic Datasheets

Basic Performance	Test Condition	Test Method	EASTMAN USA/6002
density		D792	1.2

machinability	Test Condition	Test Method	EASTMAN USA/6002
drying temperature			70℃(160℉)
drying time			6小时
film temperature			15-30℃(60-80℉)
Processing melting temperature			230-280℃(450-530℉)

thermal performance	Test Condition	Test Method	EASTMAN USA/6002
Bending temperature	0.455MPa(66 psi)	D648	73℃(164℉)
Bending temperature		1.82MPa(264 psi)	D648	65℃(149℉)
Hot deformation temperature	1.8 MPa, Unannealed	ASTM D648	125 °C
Hot deformation temperature		0.45 MPa, Unannealed	ASTM D648	135 °C

mechanical properties	Test Condition	Test Method	EASTMAN USA/6002
Bending modulus		ISO 178	1850MPa
Bending modulus			D790	2000MPa(2.9×10
bending strength		ISO 178	65MPa
elongation	Break	ASTM D638	15 %
Impact resistance (perforation), energy @ maximum load	@-40℃(-40℉)	D3763	48 J/m(35 ft bf)
Impact resistance (perforation), energy @ maximum load		@23℃(73℉)	D3763	42 J(31 ft bf)
Impact strength of cantilever beam gap	@23℃(73?H)，切口	D256	80 J/m(1.5 ft bf/in)
		@23℃，切口	ISO 180	7.8kJ/m
		@23℃(73℉)，未切口	D4812	NB J/m(NB ft bf/in)
		@-40℃，切口	ISO 180	4.8kJ/m
		@-40℃(-40?H)，切口	D256	40 J/m(0.7 ft bf/in)
		@-40℃(-40℉)，未切口	D4812	NB J/m(NB ft bf/in)
Rockwell hardness	R刻度	D785	103
Stretching degree	@Yield	D638	5%
		@Break	ISO 527	200%
		@Yield	ISO 527	4%
		@Break	D638	320%
Tensile modulus		ISO 527	1800MPa
tensile strength	Yield	ASTM D638	60.0 Mpa
		@Break	ISO 527	46MPa
		@Yield	ISO 527	47MPa
		Yield	D790	69MPa(10000 psi)
Tensile stress	@Break	D638	51MPa（7400 psi）
Tensile stress		@Yield	D638	47MPa（6900 psi）

Electrical performance	Test Condition	Test Method	EASTMAN USA/6002
Dielectric strength	2.00 mm	ASTM D149	15 KV/mm
Volume resistivity		ASTM D257	> 1.0E+16 ohms·cm

Physical properties	Test Condition	Test Method	EASTMAN USA/6002
gloss		D1003	0.3%
melt mass-flow rate	300°C/1.2 kg	ASTM D1238	20 g/10 min
Total transmittance		D1003	91%
Transmittance rate		D1003	89%
Water absorption rate	Saturation, 23°C	ISO 62	0.30 %
Water absorption rate		Equilibrium, 23°C, 50% RH	ISO 62	0.15 %

flammability	Test Condition	Test Method	EASTMAN USA/6002
UL flame retardant rating	3.2 mm	UL 94	V-2

injection	Test Condition	Test Method	EASTMAN USA/6002
drying temperature			120 °C
drying time			3.0 to 4.0 hr
Mold temperature			60 to 80 °C
Processing (melt) temperature			280 to 290 °C
Spray nozzle temperature			285 to 295 °C
Temperature at the rear of the barrel			265 to 275 °C
Temperature in the middle of the barrel			280 to 290 °C

Get App

Top