plas
Log In
CategoriesAll

Material Comparison

Product Info
Product Name
Brand Name
Usages
Properties
Certificates
DAP Synres-Almoco DAP 5553 Synres-Almoco BV
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--

Plastic Datasheets

thermal performanceTest ConditionTest MethodSynres-Almoco BV/Synres-Almoco DAP 5553
Hot deformation temperature8.0MPa,UnannealedISO 75-2/C120to140 °C
1.8MPa,UnannealedISO 75-2/A>180 °C
Linear coefficient of thermal expansionMD：50to100°CISO 11359-25.0E-6到1.0E-5 cm/cm/°C
thermal conductivityASTME14610.90to1.1 W/m/K
mechanical propertiesTest ConditionTest MethodSynres-Almoco BV/Synres-Almoco DAP 5553
Bending modulusInjectionISO 17812000to18000 MPa
Compression MoldedISO 1788000to12000 MPa
bending strengthInjectionISO 178150to180 MPa
Compression MoldedISO 17890.0to110 MPa
Compressive stressISO 604150to200 MPa
Tensile modulusCompression MoldedISO 527-26000to9000 MPa
InjectionISO 527-210000to16000 MPa
tensile strengthCompressionMoldedISO 527-235.0to60.0 MPa
InjectionISO 527-280.0to100 MPa
Electrical performanceTest ConditionTest MethodSynres-Almoco BV/Synres-Almoco DAP 5553
Arc resistanceASTM D495PLC 4
Compared to the anti leakage trace indexIEC 60112PLC 1
Dielectric strengthIEC 60243-115to20 kV/mm
Dissipation factor1MHzIEC 602500.010to0.030
100HzIEC 602500.010to0.030
Relative permittivity100HzIEC 602504.505.00
1MHzIEC 602504.004.50
Surface resistivityIEC 600931.0E+14到1.0E+15 ohms
Volume resistivityIEC 600931.0E+14到1.0E+15 ohms·cm
Physical propertiesTest ConditionTest MethodSynres-Almoco BV/Synres-Almoco DAP 5553
Apparent densityISO 600.75to0.90 g/cm³
densityISO 11831.80to2.00 g/cm³
Shrinkage rateISO 2577<0.050 %
MD：--4ISO 25770.15to0.45 %
MD：--3ISO 25770.15to0.35 %
Water absorption rate23°C,24hrISO 62<0.20 %
impact performanceTest ConditionTest MethodSynres-Almoco BV/Synres-Almoco DAP 5553
Charpy Notched Impact StrengthInjectionISO 179/1eA4.0to8.0 kJ/m²
Compression MoldedISO 179/1eA3.5to6.0 kJ/m²
Impact strength of simply supported beam without notchInjectionISO 179/1eU10to15 kJ/m²
Compression MoldedISO 179/1eU5.0to10 kJ/m²
flammabilityTest ConditionTest MethodSynres-Almoco BV/Synres-Almoco DAP 5553
Burning wire flammability indexIEC 60695-2-12960 °C
Hot filament ignition temperatureIEC 60695-2-13875 °C
UL flame retardant rating0.60mmUL 94V-0

Contact Us

Get App

Top