Log In | Sign Up
CategoriesAll
Plastic Raw Materials
Modified Plastics
Plastic Additives
Color Masterbatch
Plastic Datasheets
Plastic News
About Us

Material Comparison

Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PC FXE121R BK1A184T SABIC INNOVATIVE NANSHA
LEXAN™ 
Profile、building materials
Low viscosity、Flame retardant、transparent
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--

Plastic Datasheets

Impact resistanceTest ConditionTest MethodSABIC INNOVATIVE NANSHA/FXE121R BK1A184T
Charpy Notched Impact Strength23°CISO 179/1eA65 kJ/m²
Impact strength of simply supported beam without notch-30°CISO 179/1eU无断裂
Charpy Notched Impact Strength-30°CISO 179/1eA12 kJ/m²
Impact strength of simply supported beam without notch23°CISO 179/1eU无断裂
Suspended wall beam without notch impact strength23°CASTM D48123200 J/m
23°C5ISO 180/1U无断裂
Dart impact23°C, Energy at PeakASTM D376362.0 J
Impact strength of cantilever beam gapASTM D1822546 kJ/m²
Suspended wall beam without notch impact strength-30°C5ISO 180/1U无断裂
Dart impact23°CASTM D3029169 J
hardnessTest ConditionTest MethodSABIC INNOVATIVE NANSHA/FXE121R BK1A184T
Rockwell hardnessM 级ASTM D78570
R 级ASTM D785118
Mechanical propertiesTest ConditionTest MethodSABIC INNOVATIVE NANSHA/FXE121R BK1A184T
elongation断裂ASTM D638130 %
屈服ASTM D6387.0 %
Taber abraser1000 Cycles, 1000 g, CS-17 转轮ASTM D104410.0 mg
bending strength屈服, 50.0 mm 跨距ASTM D79096.0 Mpa
tensile strength 断裂ASTM D63868.0 Mpa
屈服ASTM D63862.0 Mpa
Flexural modulus50.0 mm 跨距ASTM D7902340 Mpa
Electrical performanceTest ConditionTest MethodSABIC INNOVATIVE NANSHA/FXE121R BK1A184T
Volume resistivityASTM D257> 1.0E+17 ohms·cm
dielectric constant60 HzASTM D1503.17
Dissipation Factor60 HzASTM D1509.0E-4
50 HzASTM D1509.0E-4
dielectric constant1 MHzASTM D1502.96
Hot wire ignition (HWI)UL 746PLC 2
dielectric strength3.20 mm, in AirASTM D14915 KV/mm
High Voltage Arc Traceability Rate (HVTR)UL 746PLC 2
Compared to the Leakage Tracking Index (CTI)UL 746PLC 2
Dissipation Factor1 MHzASTM D1500.010
High arc combustion index (HAI)UL 746PLC 1
dielectric constant50 kHzASTM D1503.17
optical performance Test ConditionTest MethodSABIC INNOVATIVE NANSHA/FXE121R BK1A184T
refractive indexASTM D5421.586
transmissivity2540 µmASTM D100388.0 %
Haze ratio2540 µmASTM D10031.0 %
flammabilityTest ConditionTest MethodSABIC INNOVATIVE NANSHA/FXE121R BK1A184T
UL flame retardant rating0.71 mmUL 94HB
Radiation board gradeUL UnspecifiedTRUE
physical property Test ConditionTest MethodSABIC INNOVATIVE NANSHA/FXE121R BK1A184T
Water absorption rate平衡, 23°CASTM D5700.35 %
平衡, 100°CASTM D5700.58 %
Outdoor applicabilityUL 746Cf2
Water absorption rate24 hrASTM D5700.15 %
Specific volumeASTM D7920.830 cm³/g
melt mass-flow rate300°C/1.2 kgASTM D123818 g/10 min
Shrinkage rate3.20 mm，Flow内部方法0.50 - 0.70 %
Thermal performanceTest ConditionTest MethodSABIC INNOVATIVE NANSHA/FXE121R BK1A184T
thermal conductivityASTM C1770.25 W/m/K
Linear coefficient of thermal expansion-40 到 95°C，流动ASTM E8316.8E-5 cm/cm/°C
specific heatASTM C3511250 J/kg/°C
Heat distortion temperature1.8 MPa, 未退火, 6.40 mm，HDTASTM D648129 °C
RTI ImpUL 746130 °C
RTIUL 746130 °C
vicatASTM D15257154 °C
Heat distortion temperature0.45 MPa, 未退火, 6.40 mm，HDTASTM D648137 °C
RTI ElecUL 746130 °C
injectionTest ConditionTest MethodSABIC INNOVATIVE NANSHA/FXE121R BK1A184T
screw speed40 to 70 rpm
Suggested maximum moisture content0.020 %
Processing (melt) temperature280 to 305 °C
drying temperature120 °C
Suggested injection volume40 to 60 %
drying time3.0 to 4.0 hr
Temperature in the middle of the barrel270 to 295 °C
Temperature at the rear of the barrel260 to 280 °C
Exhaust hole depth0.025 to 0.076 mm
Temperature at the front of the material cylinder280 to 305 °C
Back pressure0.300 to 0.700 Mpa
Temperature70 to 95 °C
Spray nozzle temperature275 to 300 °C

Contact Us

Get App

Top