Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PPO/PA GTX910-111 SABIC INNOVATIVE US
NORYL GTX™
Electrical applications、electrical equipment
High mobility、Chemical resistance、High rigidity
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | SABIC INNOVATIVE US/GTX910-111 |
|---|---|---|---|
| Dart impact | -30°C, Energy at Peak | ASTM D3763 | 39.0 J |
| 23°C, Energy at Peak | ASTM D3763 | 50.0 J |
| hardness | Test Condition | Test Method | SABIC INNOVATIVE US/GTX910-111 |
|---|---|---|---|
| Rockwell hardness | R 级 | ASTM D785 | 116 |
| Mechanical properties | Test Condition | Test Method | SABIC INNOVATIVE US/GTX910-111 |
|---|---|---|---|
| elongation | 断裂 | ASTM D638 | 60 % |
| tensile strength | 断裂 | ASTM D638 | 55.0 Mpa |
| bending strength | 屈服, 100 mm 跨距 | ASTM D790 | 95.0 Mpa |
| tensile strength | 屈服 | ASTM D638 | 59.0 Mpa |
| Flexural modulus | 100 mm 跨距 | ASTM D790 | 2240 Mpa |
| Electrical performance | Test Condition | Test Method | SABIC INNOVATIVE US/GTX910-111 |
|---|---|---|---|
| Hot wire ignition (HWI) | UL 746 | PLC 3 | |
| arc resistance | ASTM D495 | PLC 7 | |
| High Voltage Arc Traceability Rate (HVTR) | UL 746 | PLC 4 | |
| Compared to the Leakage Tracking Index (CTI) | UL 746 | PLC 1 | |
| High arc combustion index (HAI) | UL 746 | PLC 0 |
| flammability | Test Condition | Test Method | SABIC INNOVATIVE US/GTX910-111 |
|---|---|---|---|
| UL flame retardant rating | 1.5 mm | UL 94 | HB |
| physical property | Test Condition | Test Method | SABIC INNOVATIVE US/GTX910-111 |
|---|---|---|---|
| Shrinkage rate | 横向流动 : 3.20 mm | 内部方法 | 1.0 - 1.2 % |
| Water absorption rate | 24 hr, 50% RH | ASTM D570 | 0.50 % |
| Shrinkage rate | 流动 : 130°C, 1小时 | ASTM D955 | 1.6 - 1.8 % |
| Water absorption rate | 平衡, 50% RH | ASTM D570 | 1.0 % |
| Shrinkage rate | 流动 : 3.20 mm | 内部方法 | 1.1 - 1.3 % |
| Thermal performance | Test Condition | Test Method | SABIC INNOVATIVE US/GTX910-111 |
|---|---|---|---|
| Linear coefficient of thermal expansion | 流动 : -40 到 95°C | ASTM E831 | 9.0E-5 cm/cm/°C |
| vicat | ASTM D15254 | 232 °C | |
| Linear coefficient of thermal expansion | 流动 : 60 到 138°C | ASTM E831 | 1.3E-4 cm/cm/°C |
| 横向 : 60 到 138°C | ASTM E831 | 1.3E-4 cm/cm/°C | |
| Heat distortion temperature | 1.8 MPa, 未退火, 6.40 mm，HDT | ASTM D648 | 143 °C |
| RTI Imp | UL 746 | 50.0 °C | |
| RTI | UL 746 | 50.0 °C | |
| Linear coefficient of thermal expansion | 横向 : -40 到 95°C | ASTM E831 | 9.0E-5 cm/cm/°C |
| Heat distortion temperature | 0.45 MPa, 未退火, 6.40 mm，HDT | ASTM D648 | 193 °C |
| RTI Elec | UL 746 | 50.0 °C |
| injection | Test Condition | Test Method | SABIC INNOVATIVE US/GTX910-111 |
|---|---|---|---|
| screw speed | 20 to 100 rpm | ||
| Suggested maximum moisture content | 0.070 % | ||
| Processing (melt) temperature | 280 to 305 °C | ||
| drying temperature | 95 to 105 °C | ||
| Suggested injection volume | 30 to 50 % | ||
| drying time | 3.0 to 4.0 hr | ||
| Temperature in the middle of the barrel | 270 to 305 °C | ||
| Temperature at the rear of the barrel | 265 to 305 °C | ||
| Exhaust hole depth | 0.013 to 0.038 mm | ||
| Temperature at the front of the material cylinder | 275 to 305 °C | ||
| Back pressure | 0.300 to 1.40 Mpa | ||
| Temperature | 75 to 120 °C | ||
| Spray nozzle temperature | 280 to 305 °C |
Contact Us
Get App
Top