Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
POM 100 NC010 DUPONT JAPAN
Delrin®
Thin walled products、Fitness equipment
High rigidity、High hardness、Thermal stability、high viscosity、heat-resisting
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | DUPONT JAPAN/100 NC010 |
|---|---|---|---|
| Impact strength of simply supported beam without notch | 23°C | ISO179/1eU | NoBreak |
| -30°C | ISO179/1eU | 430 kJ/m² |
| Supplementary Information | Test Condition | Test Method | DUPONT JAPAN/100 NC010 |
|---|---|---|---|
| Emission | VDA275 | <8.00 mg/kg | |
| Emissions of Organic Compounds | VDA277 | 4.00 µgC/g |
| hardness | Test Condition | Test Method | DUPONT JAPAN/100 NC010 |
|---|---|---|---|
| Rockwell hardness | M计秤 | ISO2039-2 | 90 |
| R计秤 | ISO2039-2 | 121 |
| Mechanical properties | Test Condition | Test Method | DUPONT JAPAN/100 NC010 |
|---|---|---|---|
| Nominal tensile fracture strain | ISO527-2 | 45 % | |
| Bending stress | 3.5%应变 | ISO178 | 79.0 Mpa |
| TensileCreepModule | 1hr | ISO899-1 | 2900 Mpa |
| Tensile stress | 屈服 | ISO527-2 | 72.0 Mpa |
| Tensile strain | 屈服 | ISO527-2 | 26 % |
| Tensile modulus | ISO527-2 | 3000 Mpa | |
| Flexural modulus | ISO178 | 2900 Mpa | |
| Tensile creep modulus | 1000hr | ISO899-1 | 1600 Mpa |
| compression stress | ISO604 | 110 Mpa |
| Electrical performance | Test Condition | Test Method | DUPONT JAPAN/100 NC010 |
|---|---|---|---|
| Surface Resistivity | IEC60093 | 3E+13 ohms | |
| 100Hz | IEC60250 | 3.90 | |
| CTI | IEC60112 | 600 V | |
| Dissipation Factor | 100Hz | IEC60250 | 1E-03 |
| Volume resistivity | IEC60093 | >1.0E+15 ohms·cm | |
| dielectric strength | IEC60243-1 | 41 KV/mm | |
| Dissipation Factor | 1MHz | IEC60250 | 5.5E-03 |
| 1MHz | IEC60250 | 3.80 |
| flammability | Test Condition | Test Method | DUPONT JAPAN/100 NC010 |
|---|---|---|---|
| atomization | F-value(refraction) | ISO6452 | 91 % |
| FMVSS flammability | FMVSS302 | B | |
| Burning rate 3 | 1.00mm | ISO3795 | 30 mm/min |
| UL flame retardant rating | 0.8mm | IEC60695-11-10,-20 | HB |
| 1.5mm | IEC60695-11-10,-20 | HB | |
| 0.8mm | UL94 | HB | |
| 1.5mm | UL94 | HB | |
| atomization | G-value(condensate) | ISO6452 | 1E-04 g |
| physical property | Test Condition | Test Method | DUPONT JAPAN/100 NC010 |
|---|---|---|---|
| Shrinkage rate | TD | ISO294-4 | 1.8 % |
| Water absorption rate | 饱和,23°C,2.00mm | ISO62 | 0.90 % |
| SpecificHeatCapacity of Melt | 3000 J/kg/°C | ||
| melt mass-flow rate | ISO1133 | 2.3 g/10min | |
| Melt volume flow rate | 190°C/2.16kg | ISO1133 | 1.90 cm3/10min |
| Shrinkage rate | MD | ISO294-4 | 2.2 % |
| Water absorption rate | 平衡,23°C,2.00mm,50%RH | ISO62 | 0.20 % |
| MediumDensity | 1.19 g/cm³ |
| Thermal performance | Test Condition | Test Method | DUPONT JAPAN/100 NC010 |
|---|---|---|---|
| MD：-40to23°C | ISO11359-2 | 1E-04 cm/cm/°C | |
| TD：-- | ISO11359-2 | 1.1E-04 cm/cm/°C | |
| Linear coefficient of thermal expansion | TD：AnnealingTime-Optional | ISO11359-2 | 30.0 min/mm |
| vicat | -- | ISO306/A50 | 175 °C |
| melting temperature | ISO11357-3 | 178 °C | |
| MD：-- | ISO11359-2 | 1.1E-04 cm/cm/°C | |
| TD：-40to23°C | ISO11359-2 | 1E-04 cm/cm/°C | |
| TD：EffectiveThermalDiffusivity | ISO11359-2 | 1E-07 m²/s | |
| Heat distortion temperature | 1.8MPa,未退火 | ISO75-2/A | 100 °C |
| vicat | -- | ISO306/B50 | 160 °C |
| Linear coefficient of thermal expansion | TD：AnnealingTemperature | ISO11359-2 | 160 °C |
| Heat distortion temperature | 0.45MPa,未退火 | ISO75-2/B | 160 °C |
Contact Us
Get App
Top