Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PEI VH1003-1000 SABIC INNOVATIVE US
EXTEM™
Automotive sector、aviation industry
Chemical resistance、heat-resisting、Flame retardant、high strength
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | SABIC INNOVATIVE US/VH1003-1000 |
|---|---|---|---|
| -30°C | ISO 180/1U | 无断裂 | |
| 23°C | ISO 180/1A | 4.6 kJ/m² | |
| ASTMD4812 | 无断裂 | ||
| Dart impact | 23°C,TotalEnergy | ASTM D3763 | 33.9 J |
| Impact strength of simply supported beam without notch | -30°C | ISO 179/1eU | 无断裂 |
| 23°C | ISO 179/1eU | 无断裂 | |
| 23°C | ASTM D256 | 69 J/m | |
| -30°C | ASTM D256 | 74 J/m | |
| ISO 180/1A | 5.4 kJ/m² |
| hardness | Test Condition | Test Method | SABIC INNOVATIVE US/VH1003-1000 |
|---|---|---|---|
| ball-indentation hardness | H358/30 | ISO 2039-1 | 141 Mpa |
| Electrical performance | Test Condition | Test Method | SABIC INNOVATIVE US/VH1003-1000 |
|---|---|---|---|
| Dissipation Factor | 1kHz | IEC 60250 | 1E-03 |
| Compared to the Leakage Tracking Index (CTI) | IEC 60112 | PLC 3 | |
| dielectric strength | 3.20mm,inOil | ASTM D149 | 17 KV/mm |
| dielectric constant | 1kHz | ASTM D150 | 3.41 |
| Dissipation Factor | 100Hz | IEC 60250 | 8E-03 |
| dielectric constant | 100Hz | ASTM D150 | 3.41 |
| Dissipation Factor | 50Hz | IEC 60250 | 0.025 |
| 60Hz | IEC 60250 | 0.025 | |
| 1MHz | IEC 60250 | 7E-03 |
| Mechanical properties | Test Condition | Test Method | SABIC INNOVATIVE US/VH1003-1000 |
|---|---|---|---|
| yield | ASTM D638 | 96.5 Mpa | |
| fracture | ISO 527-2/5 | 78.0 Mpa | |
| yield | ASTM D638 | 6.0 % | |
| --2 | ASTM D638 | 3520 Mpa | |
| yield | ISO 527-2/5 | 95.0 Mpa | |
| ISO 527-2/5 | 8.5 % | ||
| fracture | ASTM D638 | 96.5 Mpa | |
| ASTM D638 | 50 % | ||
| --9 | ISO 178 | 123 Mpa | |
| Yield, 100mm span | ASTM D790 | 155 Mpa | |
| --8 | ISO 178 | 3080 Mpa | |
| 50.0mm span | ASTM D790 | 3170 Mpa | |
| fracture | ISO 527-2/5 | 17 % | |
| Fracture, 50.0mm span | ASTM D790 | 159 Mpa |
| optical performance | Test Condition | Test Method | SABIC INNOVATIVE US/VH1003-1000 |
|---|---|---|---|
| Haze ratio | 2540µm | ASTM D1003 | 2.0 % |
| transmissivity | 2540µm | ASTM D1003 | 58.0 % |
| flammability | Test Condition | Test Method | SABIC INNOVATIVE US/VH1003-1000 |
|---|---|---|---|
| Hot filament ignition temperature | 3.00mm | IEC 60695-2-13 | 850 °C |
| Burning wire flammability index | 3.20mm | IEC 60695-2-12 | 960 °C |
| Limiting Oxygen Index | ISO 4589-2 | 45 % |
| physical property | Test Condition | Test Method | SABIC INNOVATIVE US/VH1003-1000 |
|---|---|---|---|
| Melt volume flow rate | 360°C/5.0kg | ISO 1133 | 8.50 cm3/10min |
| Shrinkage rate | MD:3.20mm | 内部方法 | 0.50-0.70 % |
| melt mass-flow rate | 367°C/6.6kg | ASTM D1238 | 16 g/10min |
| Water absorption rate | 平衡,23°C,50%RH | ISO 62 | 0.60 % |
| 饱和,23°C | ISO 62 | 1.8 % | |
| Shrinkage rate | TD:3.20mm | 内部方法 | 0.50-0.70 % |
| MD1 | 内部方法 | 0.50-0.70 % |
| Thermal performance | Test Condition | Test Method | SABIC INNOVATIVE US/VH1003-1000 |
|---|---|---|---|
| thermal conductivity | ASTME1530 | 0.22 W/m/K | |
| Horizontal: 23 to 150 ° C | 横向, 23到150℃ | ISO 11359-2 | 5E-05 cm/cm/°C |
| 0.45MPa, Unanealed, 6.40mm | ASTM D648 | 237 °C | |
| Flow: -40 to 150 ° C | -40到150°C | ASTME831 | 5E-05 cm/cm/°C |
| 1.8MPa, Unanealed, 64.0mm span | ISO 75-2/Af | 228 °C | |
| 1.8MPa, Unanealed, 3.20mm | ASTM D648 | 217 °C | |
| 1.8MPa, Unanealed, 6.40mm | ASTM D648 | 230 °C | |
| Horizontal: -40 to 150 ° C | 横向, -40到150°C | ASTME831 | 5E-05 cm/cm/°C |
| Flow: 23 to 150 ° C | 23到150℃ | ISO 11359-2 | 5E-05 cm/cm/°C |
| ball-indentation hardness | 125°C | IEC 60695-10-2 | Pass |
Contact Us
Get App
Top