Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

LCP C130 JAPAN POLYPLASTIC

LAPEROS®

Electrical field,Electronic field,Household appliances,Household appliances

Flame retardant,High temperature resistan,Glass fiber reinforced,High mobility

ULMSDS

Plastic Datasheets

hardness	Test Condition	Test Method	JAPAN POLYPLASTIC/C130
Rockwell hardness	M -Sale	ISO 2039-2	80

thermal performance	Test Condition	Test Method	JAPAN POLYPLASTIC/C130
Hot deformation temperature	8.0 MPa, Unannealed	ISO 75-2/C	211 °C
		0.45 MPa, Unannealed	ISO 75-2/B	250 °C
		1.8 MPa, Unannealed	ISO 75-2/A	255 °C
Linear coefficient of thermal expansion	Across Flow	ISO 11359-2	1.8E-5 cm/cm/°C
Linear coefficient of thermal expansion		Flow	ISO 11359-2	6.0E-6 cm/cm/°C
Melting temperature		ISO 11357-3	325 °C
Vicat softening temperature		ISO 306/B50	192 °C

mechanical properties	Test Condition	Test Method	JAPAN POLYPLASTIC/C130
Bending modulus	23°C	ISO 178	14000 Mpa
bending strength	23°C	ISO 178	245 Mpa
Compressive modulus		ISO 604	22000 Mpa
Compressive stress	1% Strain	ISO 604	139 Mpa
Tensile creep modulus	1 hr	ISO 899-1	13600 Mpa
Tensile creep modulus		1000 hr	ISO 899-1	11700 Mpa
Tensile modulus		ISO 527-2/1A	15000 Mpa
Tensile strain	Break	ISO 527-2/1A/5	1.9 %
tensile strength	Break	ISO 527-2/1A/5	160 Mpa

Electrical performance	Test Condition	Test Method	JAPAN POLYPLASTIC/C130
Arc resistance		Internal Method	182 sec
Compared to the anti leakage trace index		IEC 60112	PLC 3
Dielectric strength		IEC 60243-1	35 KV/mm
Dissipation factor	100 Hz	IEC 60250	0.014
Dissipation factor		1 MHz	IEC 60250	0.018
Relative permittivity	100 Hz	IEC 60250	4.20
Relative permittivity		1 MHz	IEC 60250	3.70
Surface resistivity		IEC 60093	> 1.0E+15 ohms
Volume resistivity		IEC 60093	1.0E+15 ohms·cm

Physical properties	Test Condition	Test Method	JAPAN POLYPLASTIC/C130
density		ISO 1183	1.62 g/cm³
Shrinkage rate	横向Flow	ISO 294-4	0.40 %
Shrinkage rate		Flow	ISO 294-4	0.20 %

impact performance	Test Condition	Test Method	JAPAN POLYPLASTIC/C130
Charpy Notched Impact Strength	23°C	ISO 179/1eA	25 kJ/m²
Impact strength of cantilever beam gap	23°C	ISO 180/1A	20 kJ/m²
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	28 kJ/m²
Suspended wall beam without notch impact strength	23°C	ISO 180/1U	26 kJ/m²

flammability	Test Condition	Test Method	JAPAN POLYPLASTIC/C130
Extreme Oxygen Index		ISO 4589-2	45 %
UL flame retardant rating		UL 94	V-0

injection	Test Condition	Test Method	JAPAN POLYPLASTIC/C130
Back pressure			< 3.00 Mpa
drying temperature			150 °C
drying time			4.0 to 6.0 hr
Hopper temperature			20 to 30 °C
Injection speed			快速
Mold temperature			80 to 120 °C
Processing (melt) temperature			320 to 340 °C
Spray nozzle temperature			310 to 330 °C
Suggested maximum moisture content			0.010 %
Temperature at the front of the material cylinder			310 to 320 °C
Temperature at the rear of the barrel			290 to 300 °C
Temperature in the middle of the barrel			300 to 310 °C

Get App

Top