Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PC/ABS FR3000 702985 COVESTRO GERMANY

Bayblend®

Electrical field,Electronic field,Household appliances,Household appliances,Automotive sector

Flame retardant,UV resistance,High mobility

Plastic Datasheets

thermal performance	Test Condition	Test Method	COVESTRO GERMANY/FR3000 702985
Hot deformation temperature	0.45 MPa, Unannealed	ISO 75-2/B	95.0 °C
Hot deformation temperature		1.8 MPa, Unannealed	ISO 75-2/A	85.0 °C
Vicat softening temperature		ISO 306/B120	103 °C

mechanical properties	Test Condition	Test Method	COVESTRO GERMANY/FR3000 702985
Nominal tensile fracture strain	23°C	ISO 527-2/50	40 %
Tensile modulus	23°C	ISO 527-2/1	2650 Mpa
Tensile strain	Yield, 23°C	ISO 527-2/50	3.9 %
tensile strength	Yield, 23°C	ISO 527-2/50	64.0 Mpa

Electrical performance	Test Condition	Test Method	COVESTRO GERMANY/FR3000 702985
Relative permittivity	23°C, 100 Hz	IEC 60250	3.00
Relative permittivity		23°C, 1 MHz	IEC 60250	2.90
Surface resistivity		IEC 60093	1.0E+16 ohms
Volume resistivity	23°C	IEC 60093	1.0E+16 ohms·cm

Physical properties	Test Condition	Test Method	COVESTRO GERMANY/FR3000 702985
density	23°C	ISO 1183	1.18 g/cm³
Melt Volume Flow Rate (MVR)	240°C/5.0 kg	ISO 1133	20.0 cm3/10min
Shrinkage rate	横向Flow	ISO 2577	0.40 - 0.60 %
Shrinkage rate		Flow	ISO 2577	0.40 - 0.60 %
Water absorption rate	Saturation, 23°C	ISO 62	0.40 %
Water absorption rate		Equilibrium, 23°C, 50% RH	ISO 62	0.10 %

impact performance	Test Condition	Test Method	COVESTRO GERMANY/FR3000 702985
Impact strength of cantilever beam gap	23°C	ISO 180/A	30 kJ/m²

flammability	Test Condition	Test Method	COVESTRO GERMANY/FR3000 702985
Extreme Oxygen Index		ISO 4589-2	34 %
UL flame retardant rating	2.0 mm	UL 94	5VB
UL flame retardant rating		1.5 mm	UL 94	V-0

Filling analysis	Test Condition	Test Method	COVESTRO GERMANY/FR3000 702985
ISO			PC+ABS-FR(40)
Melt viscosity	240°C	ISO 11443-A	150 Pa·s

injection	Test Condition	Test Method	COVESTRO GERMANY/FR3000 702985
Back pressure			5.00 to 15.0 Mpa
Drying Temperature - Dry Air Dryer			80 °C
Drying time - Dry Air Dryer			4.0 hr
Exhaust hole depth			0.025 to 0.075 mm
Mold temperature			60 to 90 °C
Processing (melt) temperature			240 to 270 °C
Spray nozzle temperature			255 to 265 °C
Suggested injection volume			30 to 70 %
Suggested maximum moisture content			< 0.020 %
Temperature at the front of the material cylinder			230 to 240 °C
Temperature at the rear of the barrel			220 to 230 °C
Temperature in the middle of the barrel			225 to 235 °C

Get App

Top