Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates

PC MN-3600HA TEIJIN JAPAN
PANLITE®
Electrical field,Electronic field,Automotive sector
heat-resisting,Flame retardant,Good impact resistance,Good liquidity,Halogen-free
UL
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
thermal performance | Test Condition | Test Method | TEIJIN JAPAN/MN-3600HA |
---|---|---|---|
Hot deformation temperature | 0.45MPa,Unannealed | ISO 75-2/B | 126 °C |
1.8MPa,Unannealed | ISO 75-2/A | 113 °C | |
Linear coefficient of thermal expansion | TD | ISO 11359-2 | 7E-05 cm/cm/°C |
MD | ISO 11359-2 | 7E-05 cm/cm/°C | |
RTI Elec | 1.5mm | UL 746 | 95.0 °C |
RTI Imp | 1.5mm | UL 746 | 95.0 °C |
RTI Str | 1.5mm | UL 746 | 95.0 °C |
mechanical properties | Test Condition | Test Method | TEIJIN JAPAN/MN-3600HA |
---|---|---|---|
Bending modulus | ISO 178 | 2300 Mpa | |
bending strength | ISO 178 | 95.0 Mpa | |
Tensile modulus | ISO 527-2/1 | 2350 Mpa | |
Tensile strain | Break | ISO 527-2/50 | 100 % |
Yield | ISO 527-2/50 | 8.0 % | |
tensile strength | Yield | ISO 527-2/50 | 60.0 Mpa |
Break | ISO 527-2/50 | 60.0 Mpa |
Electrical performance | Test Condition | Test Method | TEIJIN JAPAN/MN-3600HA |
---|---|---|---|
Surface resistivity | IEC 60093 | >1.0E+15 ohms |
Physical properties | Test Condition | Test Method | TEIJIN JAPAN/MN-3600HA |
---|---|---|---|
Melt Volume Flow Rate (MVR) | 280°C/5.0kg | ISO 1133 | 21.0 cm3/10min |
Shrinkage rate | MD:4.00mm | Internal Method | 0.50-0.70 % |
TD:4.00mm | Internal Method | 0.50-0.70 % | |
Water absorption rate | 23°C,24hr | ISO 62 | 0.22 % |
impact performance | Test Condition | Test Method | TEIJIN JAPAN/MN-3600HA |
---|---|---|---|
Impact strength of simply supported beam without notch | ISO 179 | NoBreak |
flammability | Test Condition | Test Method | TEIJIN JAPAN/MN-3600HA |
---|---|---|---|
Burning wire flammability index | 2.0mm | IEC 60695-2-12 | 960 °C |
3.0mm | IEC 60695-2-12 | 930 °C | |
1.5mm | IEC 60695-2-12 | 930 °C | |
1.0mm | IEC 60695-2-12 | 960 °C | |
Hot filament ignition temperature | 3.0mm | IEC 60695-2-13 | 825 °C |
1.0mm | IEC 60695-2-13 | 875 °C | |
2.0mm | IEC 60695-2-13 | 825 °C | |
1.5mm | IEC 60695-2-13 | 825 °C | |
UL flame retardant rating | 0.45mm | UL 94 | HB |
3.0mm | UL 94 | 5VA | |
2.0mm | UL 94 | 5VB | |
1.0mm | UL 94 | V-1 | |
1.5mm | UL 94 | V-0 |