Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PC EXL4419-BR6G123 SABIC INNOVATIVE NANSHA
LEXAN™
Automotive sector、Electrical appliances、Electronic field、Electrical field、Automotive interior parts、Automotive External Parts
enhance、Glass fiber reinforced、Low temperature resistanc
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
| Impact resistance | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL4419-BR6G123 |
|---|---|---|---|
| Charpy Notched Impact Strength | 23°C | ISO 179/1eA | 25 kJ/m² |
| Impact strength of simply supported beam without notch | -30°C | ISO 179/1eU | 无断裂 |
| Charpy Notched Impact Strength | -30°C | ISO 179/1eA | 15 kJ/m² |
| Impact strength of simply supported beam without notch | 23°C | ISO 179/1eU | 无断裂 |
| Suspended wall beam without notch impact strength | 23°C | ISO 180/1U | 无断裂 |
| Dart impact | 23°C, Total Energy | ASTM D3763 | 40.0 J |
| Suspended wall beam without notch impact strength | -30°C | ISO 180/1U | 无断裂 |
| Mechanical properties | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL4419-BR6G123 |
|---|---|---|---|
| Tensile modulus | --2 | ASTM D638 | 3300 Mpa |
| tensile strength | 断裂 | ISO 527-2/5 | 43.0 Mpa |
| 屈服3 | ASTM D638 | 53.0 Mpa | |
| elongation | 断裂3 | ASTM D638 | 20 % |
| Flexural modulus | --5 | ISO 178 | 3300 Mpa |
| bending strength | 屈服, 50.0 mm 跨距4 | ASTM D790 | 95.0 Mpa |
| --5,6 | ISO 178 | 90.0 Mpa | |
| Flexural modulus | 50.0 mm 跨距4 | ASTM D790 | 3200 Mpa |
| elongation | 屈服 | ISO 527-2/5 | 4.5 % |
| tensile strength | 屈服 | ISO 527-2/5 | 55.0 Mpa |
| elongation | 屈服3 | ASTM D638 | 4.5 % |
| tensile strength | 断裂3 | ASTM D638 | 44.0 Mpa |
| Tensile modulus | -- | ISO 527-2/1 | 3300 Mpa |
| elongation | 断裂 | ISO 527-2/5 | 13 % |
| Electrical performance | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL4419-BR6G123 |
|---|---|---|---|
| dielectric strength | 1.60 mm, in Oil | ASTM D149 | 32 KV/mm |
| dielectric constant | 1.90 GHz | 内部方法 | 2.95 |
| Volume resistivity | ASTM D257 | 1.8E+17 ohms·cm | |
| Surface Resistivity | ASTM D257 | 2.9E+17 ohms | |
| dielectric constant | 1 MHz | ASTM D150 | 3.04 |
| Dissipation Factor | 1.90 GHz | 内部方法 | 5.7E-3 |
| 1 MHz | ASTM D150 | 8.6E-3 |
| physical property | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL4419-BR6G123 |
|---|---|---|---|
| Water absorption rate | 平衡, 23°C, 50% RH | ISO 62 | 0.46 % |
| Melt volume flow rate | 300°C/1.2 kg | ISO 1133 | 10.0 cm3/10min |
| melt mass-flow rate | 300°C/1.2 kg | ASTM D1238 | 11 g/10 min |
| Water absorption rate | 饱和, 23°C | ISO 62 | 0.12 % |
| Shrinkage rate | 3.20 mm，Flow | 内部方法 | 0.20 - 0.60 % |
| Thermal performance | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL4419-BR6G123 |
|---|---|---|---|
| Linear coefficient of thermal expansion | 流动 : -40 到 40°C | ASTM E831 | 4.1E-5 cm/cm/°C |
| vicat | -- | ISO 306/B120 | 146 °C |
| -- | ASTM D152510 | 145 °C | |
| ball-indentation hardness | 73 到 77°C | IEC 60695-10-2 | 通过 |
| Linear coefficient of thermal expansion | 横向 : -40°C | ISO 11359-2 | 6.9E-5 cm/cm/°C |
| vicat | -- | ISO 306/B50 | 144 °C |
| Heat distortion temperature | 1.8 MPa, 未退火, 4.00 mm, 64.0 mm 跨距9，HDT | ISO 75-2/Af | 134 °C |
| Linear coefficient of thermal expansion | 横向 : -40 到 40°C | ASTM E831 | 6.9E-5 cm/cm/°C |
| Heat distortion temperature | 1.8 MPa, 未退火, 3.20 mm，HDT | ASTM D648 | 135 °C |
| injection | Test Condition | Test Method | SABIC INNOVATIVE NANSHA/EXL4419-BR6G123 |
|---|---|---|---|
| screw speed | 40 to 70 rpm | ||
| Suggested maximum moisture content | 0.020 % | ||
| Processing (melt) temperature | 310 to 330 °C | ||
| drying temperature | 120 °C | ||
| Suggested injection volume | 40 to 60 % | ||
| drying time | 3.0 to 4.0 hr | ||
| Temperature in the middle of the barrel | 300 to 320 °C | ||
| Temperature at the rear of the barrel | 290 to 310 °C | ||
| Exhaust hole depth | 0.025 to 0.076 mm | ||
| Temperature at the front of the material cylinder | 310 to 330 °C | ||
| Back pressure | 0.300 to 0.700 Mpa | ||
| Temperature | 80 to 115 °C | ||
| Spray nozzle temperature | 305 to 325 °C |
Contact Us
Get App
Top