Material Comparison
Product Info
Product Name
Brand Name
Usages
Properties
Certificates

TPE 6356 DUPONT USA
Hytrel®
pipeline,sheet,Wire and cable,Industrial applications,Automotive sector,Fitness equipment
Thermal stability
UL
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Plastic Datasheets
hardness | Test Condition | Test Method | DUPONT USA/6356 |
---|---|---|---|
Shore hardness | ShoreD | ISO 868 | 63 |
ShoreD,15Sec | ISO 868 | 57 |
Supplementary Information | Test Condition | Test Method | DUPONT USA/6356 |
---|---|---|---|
EmissionofOrganicCompounds | VDA277 | 2.50 µgC/g | |
Odor | VDA270 | 2.50 |
thermal performance | Test Condition | Test Method | DUPONT USA/6356 |
---|---|---|---|
Brittle temperature | ISO 974 | -96.0 °C | |
Glass transition temperature | ISO 11357-2 | 0.00 °C | |
Hot deformation temperature | 0.45MPa,Unannealed | ISO 75-2/B | 80.0 °C |
1.8MPa,Unannealed | ISO 75-2/A | 45.0 °C | |
Linear coefficient of thermal expansion | TD:23to55°C | ASTME831 | 1.7E-04 cm/cm/°C |
MD:-- | ISO 11359-2 | 1.9E-04 cm/cm/°C | |
TD:-40to23°C | ISO 11359-2 | 1.5E-04 cm/cm/°C | |
MD:-40to23°C | ISO 11359-2 | 1.6E-04 cm/cm/°C | |
TD:-- | ISO 11359-2 | 1.8E-04 cm/cm/°C | |
TD:EffectiveThermalDiffusivity | ISO 11359-2 | 5.44E-08 m²/s | |
Melting temperature | ISO 11357-3 | 210 °C | |
Vicat softening temperature | -- | ISO 306/B50 | 100 °C |
-- | ISO 306/A50 | 195 °C |
mechanical properties | Test Condition | Test Method | DUPONT USA/6356 |
---|---|---|---|
Bending modulus | ISO 178 | 290 Mpa | |
Nominal tensile fracture strain | ISO 527-2 | 500 % | |
Tensile creep modulus | 1hr | ISO 899-1 | 248 Mpa |
1000hr | ISO 899-1 | 182 Mpa | |
Tensile modulus | ISO 527-2 | 280 Mpa | |
Tensile strain | Yield | ISO 527-2 | 31 % |
Break | ISO 527-2 | >300 % | |
tensile strength | 5.0%Strain | ISO 527-2 | 12.0 Mpa |
10%Strain | ISO 527-2 | 15.0 Mpa | |
100%Strain | ISO 527-2 | 19.0 Mpa | |
Break | ISO 527-2 | 43.0 Mpa | |
50%Strain | ISO 527-2 | 18.8 Mpa | |
Yield | ISO 527-2 | 20.0 Mpa | |
Wear resistance | ISO 4649 | 110 mm³ |
Electrical performance | Test Condition | Test Method | DUPONT USA/6356 |
---|---|---|---|
Dielectric strength | IEC 60243-1 | 20 KV/mm | |
Dissipation factor | 1MHz | IEC 60250 | 0.036 |
100Hz | IEC 60250 | 0.012 | |
Relative permittivity | 100Hz | IEC 60250 | 4.60 |
1MHz | IEC 60250 | 4.10 | |
Surface resistivity | IEC 60093 | >1.0E+15 ohms | |
Volume resistivity | IEC 60093 | 8E+13 ohms·cm |
Physical properties | Test Condition | Test Method | DUPONT USA/6356 |
---|---|---|---|
density | ISO 1183 | 1.22 g/cm³ | |
MediumDensity | 1.06 g/cm³ | ||
melt mass-flow rate | 230°C/2.16kg | ISO 1133 | 9.0 g/10min |
Melt Volume Flow Rate (MVR) | 230°C/2.16kg | ISO 1133 | 8.50 cm3/10min |
Shrinkage rate | MD | ISO 294-4 | 1.5 % |
TD | ISO 294-4 | 1.5 % | |
SpecificHeatCapacity of Melt | 2150 J/kg/°C | ||
ThermalConductivityofMelt | 0.15 W/m/K | ||
Water absorption rate | Equilibrium,23°C,2.00mm,50%RH | ISO 62 | 0.20 % |
23°C,24hr | ISO 62 | 0.50 % | |
Saturation,23°C,2.00mm | ISO 62 | 0.60 % |
impact performance | Test Condition | Test Method | DUPONT USA/6356 |
---|---|---|---|
Charpy Notched Impact Strength | 23°C,Partial Break | ISO 179/1eA | 120 kJ/m² |
-30°C | ISO 179/1eA | 25 kJ/m² | |
-40°C | ISO 179/1eA | 15 kJ/m² | |
Impact strength of cantilever beam gap | -40°C | ISO 180/1A | 19 kJ/m² |
23°C | ISO 180/1A | 81 kJ/m² | |
23°C | ISO 8256/1 | 300 kJ/m² |
flammability | Test Condition | Test Method | DUPONT USA/6356 |
---|---|---|---|
Extreme Oxygen Index | ISO 4589-2 | 21 % | |
FMVSS flammability | FMVSS302 | SE | |
Fogging-G-value | condensate | ISO 6452 | 1E-04 g |
UL flame retardant rating | 3.0mm | IEC 60695-11-10,-20 | HB |
3.0mm | UL 94 | HB | |
1.5mm | IEC 60695-11-10,-20 | HB | |
1.5mm | UL 94 | HB |
elastomer | Test Condition | Test Method | DUPONT USA/6356 |
---|---|---|---|
tear strength | 横向Flow | ISO 34-1 | 150 kN/m |
Flow | ISO 34-1 | 160 kN/m |